2 files changed, 27 insertions, 4 deletions
diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,imx7ulp-sim.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,imx7ulp-sim.txt
new file mode 100644
index 000000000000..7d0c7f002401
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/freescale/fsl,imx7ulp-sim.txt
@@ -0,0 +1,16 @@
+Freescale i.MX7ULP System Integration Module
+----------------------------------------------
+The system integration module (SIM) provides system control and chip configuration
+registers. In this module, chip revision information is located in JTAG ID register,
+and a set of registers have been made available in DGO domain for SW use, with the
+objective to maintain its value between system resets.
+
+Required properties:
+- compatible:	Should be "fsl,imx7ulp-sim".
+- reg:		Specifies base physical address and size of the register sets.
+
+Example:
+sim: sim@410a3000 {
+	compatible = "fsl,imx7ulp-sim", "syscon";
+	reg = <0x410a3000 0x1000>;
+};
diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
index 27784b6edfed..72d481c8dd48 100644
--- a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
+++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
@@ -58,7 +58,11 @@ This binding for the SCU power domain providers uses the generic power
 domain binding[2].
 
 Required properties:
-- compatible:		Should be "fsl,imx8qxp-scu-pd".
+- compatible:		Should be one of:
+			  "fsl,imx8qm-scu-pd",
+			  "fsl,imx8qxp-scu-pd"
+			followed by "fsl,scu-pd"
+
 - #power-domain-cells:	Must be 1. Contains the Resource ID used by
 			SCU commands.
 			See detailed Resource ID list from:
@@ -70,7 +74,10 @@ Clock bindings based on SCU Message Protocol
 This binding uses the common clock binding[1].
 
 Required properties:
-- compatible:		Should be "fsl,imx8qxp-clock".
+- compatible:		Should be one of:
+			  "fsl,imx8qm-clock"
+			  "fsl,imx8qxp-clock"
+			followed by "fsl,scu-clk"
 - #clock-cells:		Should be 1. Contains the Clock ID value.
 - clocks:		List of clock specifiers, must contain an entry for
 			each required entry in clock-names
@@ -137,7 +144,7 @@ firmware {
 			  &lsio_mu1 1 3>;
 
 		clk: clk {
-			compatible = "fsl,imx8qxp-clk";
+			compatible = "fsl,imx8qxp-clk", "fsl,scu-clk";
 			#clock-cells = <1>;
 		};
 
@@ -154,7 +161,7 @@ firmware {
 		};
 
 		pd: imx8qx-pd {
-			compatible = "fsl,imx8qxp-scu-pd";
+			compatible = "fsl,imx8qxp-scu-pd", "fsl,scu-pd";
 			#power-domain-cells = <1>;
 		};