Merge tag 'input-for-v6.12-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:

 - support for PixArt PS/2 touchpad

 - updates to tsc2004/5, usbtouchscreen, and zforce_ts drivers

 - support for GPIO-only mode for ADP55888 controller

 - support for touch keys in Zinitix driver

 - support for querying density of Synaptics sensors

 - sysfs interface for Goodex "Berlin" devices to read and write touch
   IC registers

 - more quirks to i8042 to handle various Tuxedo laptops

 - a number of drivers have been converted to using "guard" notation
   when acquiring various locks, as well as using other cleanup
   functions to simplify releasing of resources (with more drivers to
   follow)

 - evdev will limit amount of data that can be written into an evdev
   instance at a given time to 4096 bytes (170 input events) to avoid
   holding evdev->mutex for too long and starving other users

 - Spitz has been converted to use software nodes/properties to describe
   its matrix keypad and GPIO-connected LEDs

 - msc5000_ts, msc_touchkey and keypad-nomadik-ske drivers have been
   removed since noone in mainline have been using them

 - other assorted cleanups and fixes

* tag 'input-for-v6.12-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (98 commits)
  ARM: spitz: fix compile error when matrix keypad driver is enabled
  Input: hynitron_cstxxx - drop explicit initialization of struct i2c_device_id::driver_data to 0
  Input: adp5588-keys - fix check on return code
  Input: Convert comma to semicolon
  Input: i8042 - add TUXEDO Stellaris 15 Slim Gen6 AMD to i8042 quirk table
  Input: i8042 - add another board name for TUXEDO Stellaris Gen5 AMD line
  Input: tegra-kbc - use of_property_read_variable_u32_array() and of_property_present()
  Input: ps2-gpio - use IRQF_NO_AUTOEN flag in request_irq()
  Input: ims-pcu - fix calling interruptible mutex
  Input: zforce_ts - switch to using asynchronous probing
  Input: zforce_ts - remove assert/deassert wrappers
  Input: zforce_ts - do not hardcode interrupt level
  Input: zforce_ts - switch to using devm_regulator_get_enable()
  Input: zforce_ts - stop treating VDD regulator as optional
  Input: zforce_ts - make zforce_idtable constant
  Input: zforce_ts - use dev_err_probe() where appropriate
  Input: zforce_ts - do not ignore errors when acquiring regulator
  Input: zforce_ts - make parsing of contacts less confusing
  Input: zforce_ts - switch to using get_unaligned_le16
  Input: zforce_ts - use guard notation when acquiring mutexes
  ...

14 files changed, 548 insertions, 272 deletions

diff --git a/Documentation/devicetree/bindings/input/adi,adp5588.yaml b/Documentation/devicetree/bindings/input/adi,adp5588.yaml
index 26ea66834ae2..336bc352579a 100644
--- a/Documentation/devicetree/bindings/input/adi,adp5588.yaml
+++ b/Documentation/devicetree/bindings/input/adi,adp5588.yaml
@@ -49,7 +49,10 @@ properties:
   interrupt-controller:
     description:
       This property applies if either keypad,num-rows lower than 8 or
-      keypad,num-columns lower than 10.
+      keypad,num-columns lower than 10. This property is optional if
+      keypad,num-rows or keypad,num-columns are not specified as the
+      device is then configured to be used purely for gpio during which
+      interrupts may or may not be utilized.
 
   '#interrupt-cells':
     const: 2
@@ -65,13 +68,23 @@ properties:
     minItems: 1
     maxItems: 2
 
+dependencies:
+  keypad,num-rows:
+    - linux,keymap
+    - keypad,num-columns
+  keypad,num-columns:
+    - linux,keymap
+    - keypad,num-rows
+  linux,keymap:
+    - keypad,num-rows
+    - keypad,num-columns
+    - interrupts
+  interrupt-controller:
+    - interrupts
+
 required:
   - compatible
   - reg
-  - interrupts
-  - keypad,num-rows
-  - keypad,num-columns
-  - linux,keymap
 
 unevaluatedProperties: false
 
@@ -108,4 +121,19 @@ examples:
             >;
         };
     };
+
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        gpio@34 {
+            compatible = "adi,adp5588";
+            reg = <0x34>;
+
+            #gpio-cells = <2>;
+            gpio-controller;
+        };
+    };
+
 ...
diff --git a/Documentation/devicetree/bindings/input/rotary-encoder.txt b/Documentation/devicetree/bindings/input/rotary-encoder.txt
deleted file mode 100644
index a644408b33b8..000000000000
--- a/Documentation/devicetree/bindings/input/rotary-encoder.txt
+++ /dev/null
@@ -1,50 +0,0 @@
-Rotary encoder DT bindings
-
-Required properties:
-- gpios: a spec for at least two GPIOs to be used, most significant first
-
-Optional properties:
-- linux,axis: the input subsystem axis to map to this rotary encoder.
-  Defaults to 0 (ABS_X / REL_X)
-- rotary-encoder,steps: Number of steps in a full turnaround of the
-  encoder. Only relevant for absolute axis. Defaults to 24 which is a
-  typical value for such devices.
-- rotary-encoder,relative-axis: register a relative axis rather than an
-  absolute one. Relative axis will only generate +1/-1 events on the input
-  device, hence no steps need to be passed.
-- rotary-encoder,rollover: Automatic rollover when the rotary value becomes
-  greater than the specified steps or smaller than 0. For absolute axis only.
-- rotary-encoder,steps-per-period: Number of steps (stable states) per period.
-  The values have the following meaning:
-  1: Full-period mode (default)
-  2: Half-period mode
-  4: Quarter-period mode
-- wakeup-source: Boolean, rotary encoder can wake up the system.
-- rotary-encoder,encoding: String, the method used to encode steps.
-  Supported are "gray" (the default and more common) and "binary".
-
-Deprecated properties:
-- rotary-encoder,half-period: Makes the driver work on half-period mode.
-  This property is deprecated. Instead, a 'steps-per-period ' value should
-  be used, such as "rotary-encoder,steps-per-period = <2>".
-
-See Documentation/input/devices/rotary-encoder.rst for more information.
-
-Example:
-
-		rotary@0 {
-			compatible = "rotary-encoder";
-			gpios = <&gpio 19 1>, <&gpio 20 0>; /* GPIO19 is inverted */
-			linux,axis = <0>; /* REL_X */
-			rotary-encoder,encoding = "gray";
-			rotary-encoder,relative-axis;
-		};
-
-		rotary@1 {
-			compatible = "rotary-encoder";
-			gpios = <&gpio 21 0>, <&gpio 22 0>;
-			linux,axis = <1>; /* ABS_Y */
-			rotary-encoder,steps = <24>;
-			rotary-encoder,encoding = "binary";
-			rotary-encoder,rollover;
-		};
diff --git a/Documentation/devicetree/bindings/input/rotary-encoder.yaml b/Documentation/devicetree/bindings/input/rotary-encoder.yaml
new file mode 100644
index 000000000000..e315aab7f584
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/rotary-encoder.yaml
@@ -0,0 +1,90 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/rotary-encoder.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rotary encoder
+
+maintainers:
+  - Frank Li <Frank.Li@nxp.com>
+
+description:
+  See Documentation/input/devices/rotary-encoder.rst for more information.
+
+properties:
+  compatible:
+    const: rotary-encoder
+
+  gpios:
+    minItems: 2
+
+  linux,axis:
+    default: 0
+    description:
+      the input subsystem axis to map to this rotary encoder.
+      Defaults to 0 (ABS_X / REL_X)
+
+  rotary-encoder,steps:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 24
+    description:
+      Number of steps in a full turnaround of the
+      encoder. Only relevant for absolute axis. Defaults to 24 which is a
+      typical value for such devices.
+
+  rotary-encoder,relative-axis:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      register a relative axis rather than an
+      absolute one. Relative axis will only generate +1/-1 events on the input
+      device, hence no steps need to be passed.
+
+  rotary-encoder,rollover:
+    $ref: /schemas/types.yaml#/definitions/int32
+    description:
+      Automatic rollover when the rotary value becomes
+      greater than the specified steps or smaller than 0. For absolute axis only.
+
+  rotary-encoder,steps-per-period:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 1
+    enum: [1, 2, 4]
+    description: |
+      Number of steps (stable states) per period.
+      The values have the following meaning:
+      1: Full-period mode (default)
+      2: Half-period mode
+      4: Quarter-period mode
+
+  wakeup-source: true
+
+  rotary-encoder,encoding:
+    $ref: /schemas/types.yaml#/definitions/string
+    description: the method used to encode steps.
+    enum: [gray, binary]
+
+  rotary-encoder,half-period:
+    $ref: /schemas/types.yaml#/definitions/flag
+    deprecated: true
+    description:
+      Makes the driver work on half-period mode.
+      This property is deprecated. Instead, a 'steps-per-period ' value should
+      be used, such as "rotary-encoder,steps-per-period = <2>".
+
+required:
+  - compatible
+  - gpios
+
+additionalProperties: false
+
+examples:
+  - |
+    rotary {
+        compatible = "rotary-encoder";
+        gpios = <&gpio 19 1>, <&gpio 20 0>; /* GPIO19 is inverted */
+        linux,axis = <0>; /* REL_X */
+        rotary-encoder,encoding = "gray";
+        rotary-encoder,relative-axis;
+    };
+
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt
deleted file mode 100644
index afa38dc069f0..000000000000
--- a/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt
+++ /dev/null
@@ -1,71 +0,0 @@
-* Analog Devices AD7879(-1)/AD7889(-1) touchscreen interface (SPI/I2C)
-
-Required properties:
-- compatible			: for SPI slave, use "adi,ad7879"
-				  for I2C slave, use "adi,ad7879-1"
-- reg				: SPI chipselect/I2C slave address
-				  See spi-bus.txt for more SPI slave properties
-- interrupts			: touch controller interrupt
-- touchscreen-max-pressure	: maximum reported pressure
-- adi,resistance-plate-x	: total resistance of X-plate (for pressure
-				  calculation)
-Optional properties:
-- touchscreen-swapped-x-y	: X and Y axis are swapped (boolean)
-- adi,first-conversion-delay	: 0-12: In 128us steps (starting with 128us)
-				  13  : 2.560ms
-				  14  : 3.584ms
-				  15  : 4.096ms
-				  This property has to be a '/bits/ 8' value
-- adi,acquisition-time		: 0: 2us
-				  1: 4us
-				  2: 8us
-				  3: 16us
-				  This property has to be a '/bits/ 8' value
-- adi,median-filter-size	: 0: disabled
-				  1: 4 measurements
-				  2: 8 measurements
-				  3: 16 measurements
-				  This property has to be a '/bits/ 8' value
-- adi,averaging			: 0: 2 middle values (1 if median disabled)
-				  1: 4 middle values
-				  2: 8 middle values
-				  3: 16 values
-				  This property has to be a '/bits/ 8' value
-- adi,conversion-interval:	: 0    : convert one time only
-				  1-255: 515us + val * 35us (up to 9.440ms)
-				  This property has to be a '/bits/ 8' value
-- gpio-controller		: Switch AUX/VBAT/GPIO pin to GPIO mode
-
-Example:
-
-	touchscreen0@2c {
-		compatible = "adi,ad7879-1";
-		reg = <0x2c>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
-		touchscreen-max-pressure = <4096>;
-		adi,resistance-plate-x = <120>;
-		adi,first-conversion-delay = /bits/ 8 <3>;
-		adi,acquisition-time = /bits/ 8 <1>;
-		adi,median-filter-size = /bits/ 8 <2>;
-		adi,averaging = /bits/ 8 <1>;
-		adi,conversion-interval = /bits/ 8 <255>;
-	};
-
-	touchscreen1@1 {
-		compatible = "adi,ad7879";
-		spi-max-frequency = <5000000>;
-		reg = <1>;
-		spi-cpol;
-		spi-cpha;
-		gpio-controller;
-		interrupt-parent = <&gpio1>;
-		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
-		touchscreen-max-pressure = <4096>;
-		adi,resistance-plate-x = <120>;
-		adi,first-conversion-delay = /bits/ 8 <3>;
-		adi,acquisition-time = /bits/ 8 <1>;
-		adi,median-filter-size = /bits/ 8 <2>;
-		adi,averaging = /bits/ 8 <1>;
-		adi,conversion-interval = /bits/ 8 <255>;
-	};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/adi,ad7879.yaml b/Documentation/devicetree/bindings/input/touchscreen/adi,ad7879.yaml
new file mode 100644
index 000000000000..caa5fa3cc3f1
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/adi,ad7879.yaml
@@ -0,0 +1,150 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/adi,ad7879.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices AD7879(-1)/AD7889(-1) touchscreen interface (SPI/I2C)
+
+maintainers:
+  - Frank Li <Frank.Li@nxp.com>
+
+properties:
+  compatible:
+    description: |
+      for SPI slave, use "adi,ad7879"
+      for I2C slave, use "adi,ad7879-1"
+    enum:
+      - adi,ad7879
+      - adi,ad7879-1
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  touchscreen-max-pressure:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: maximum reported pressure
+
+  adi,resistance-plate-x:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: total resistance of X-plate (for pressure calculation)
+
+  touchscreen-swapped-x-y:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: X and Y axis are swapped (boolean)
+
+  adi,first-conversion-delay:
+    $ref: /schemas/types.yaml#/definitions/uint8
+    default: 0
+    minimum: 0
+    maximum: 15
+    description: |
+      0-12: In 128us steps (starting with 128us)
+      13  : 2.560ms
+      14  : 3.584ms
+      15  : 4.096ms
+      This property has to be a '/bits/ 8' value
+
+  adi,acquisition-time:
+    $ref: /schemas/types.yaml#/definitions/uint8
+    default: 0
+    enum: [0, 1, 2, 3]
+    description: |
+      0: 2us
+      1: 4us
+      2: 8us
+      3: 16us
+      This property has to be a '/bits/ 8' value
+
+  adi,median-filter-size:
+    $ref: /schemas/types.yaml#/definitions/uint8
+    default: 0
+    enum: [0, 1, 2, 3]
+    description: |
+      0: disabled
+      1: 4 measurements
+      2: 8 measurements
+      3: 16 measurements
+      This property has to be a '/bits/ 8' value
+
+  adi,averaging:
+    $ref: /schemas/types.yaml#/definitions/uint8
+    default: 0
+    enum: [0, 1, 2, 3]
+    description: |
+      0: 2 middle values (1 if median disabled)
+      1: 4 middle values
+      2: 8 middle values
+      3: 16 values
+      This property has to be a '/bits/ 8' value
+
+  adi,conversion-interval:
+    $ref: /schemas/types.yaml#/definitions/uint8
+    default: 0
+    description: |
+      0    : convert one time only
+      1-255: 515us + val * 35us (up to 9.440ms)
+      This property has to be a '/bits/ 8' value
+
+  gpio-controller: true
+
+  "#gpio-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - $ref: /schemas/spi/spi-peripheral-props.yaml
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        touchscreen0@2c {
+            compatible = "adi,ad7879-1";
+            reg = <0x2c>;
+            interrupt-parent = <&gpio1>;
+            interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+            touchscreen-max-pressure = <4096>;
+            adi,resistance-plate-x = <120>;
+            adi,first-conversion-delay = /bits/ 8 <3>;
+            adi,acquisition-time = /bits/ 8 <1>;
+            adi,median-filter-size = /bits/ 8 <2>;
+            adi,averaging = /bits/ 8 <1>;
+            adi,conversion-interval = /bits/ 8 <255>;
+        };
+    };
+
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        touchscreen1@1 {
+            compatible = "adi,ad7879";
+            reg = <1>;
+            spi-max-frequency = <5000000>;
+            gpio-controller;
+            #gpio-cells = <1>;
+            interrupt-parent = <&gpio1>;
+            interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+            touchscreen-max-pressure = <4096>;
+            adi,resistance-plate-x = <120>;
+            adi,first-conversion-delay = /bits/ 8 <3>;
+            adi,acquisition-time = /bits/ 8 <1>;
+            adi,median-filter-size = /bits/ 8 <2>;
+            adi,averaging = /bits/ 8 <1>;
+            adi,conversion-interval = /bits/ 8 <255>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt b/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt
deleted file mode 100644
index 399c87782935..000000000000
--- a/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt
+++ /dev/null
@@ -1,107 +0,0 @@
-Device tree bindings for TI's ADS7843, ADS7845, ADS7846, ADS7873, TSC2046
-SPI driven touch screen controllers.
-
-The node for this driver must be a child node of a SPI controller, hence
-all mandatory properties described in
-
-	Documentation/devicetree/bindings/spi/spi-bus.txt
-
-must be specified.
-
-Additional required properties:
-
-	compatible		Must be one of the following, depending on the
-				model:
-					"ti,tsc2046"
-					"ti,ads7843"
-					"ti,ads7845"
-					"ti,ads7846"
-					"ti,ads7873"
-
-	interrupts		An interrupt node describing the IRQ line the chip's
-				!PENIRQ pin is connected to.
-	vcc-supply		A regulator node for the supply voltage.
-
-
-Optional properties:
-
-	ti,vref-delay-usecs		vref supply delay in usecs, 0 for
-					external vref (u16).
-	ti,vref-mv			The VREF voltage, in millivolts (u16).
-					Set to 0 to use internal references
-					(ADS7846).
-	ti,keep-vref-on			set to keep vref on for differential
-					measurements as well
-	ti,settle-delay-usec		Settling time of the analog signals;
-					a function of Vcc and the capacitance
-					on the X/Y drivers.  If set to non-zero,
-					two samples are taken with settle_delay
-					us apart, and the second one is used.
-					~150 uSec with 0.01uF caps (u16).
-	ti,penirq-recheck-delay-usecs	If set to non-zero, after samples are
-					taken this delay is applied and penirq
-					is rechecked, to help avoid false
-					events.  This value is affected by the
-					material used to build the touch layer
-					(u16).
-	ti,x-plate-ohms			Resistance of the X-plate,
-					in Ohms (u16).
-	ti,y-plate-ohms			Resistance of the Y-plate,
-					in Ohms (u16).
-	ti,x-min			Minimum value on the X axis (u16).
-	ti,y-min			Minimum value on the Y axis (u16).
-	ti,debounce-tol			Tolerance used for filtering (u16).
-	ti,debounce-rep			Additional consecutive good readings
-					required after the first two (u16).
-	ti,pendown-gpio-debounce	Platform specific debounce time for the
-					pendown-gpio (u32).
-	pendown-gpio			GPIO handle describing the pin the !PENIRQ
-					line is connected to.
-	ti,hsync-gpios			GPIO line to poll for hsync
-	wakeup-source			use any event on touchscreen as wakeup event.
-					(Legacy property support: "linux,wakeup")
-	touchscreen-size-x		General touchscreen binding, see [1].
-	touchscreen-size-y		General touchscreen binding, see [1].
-	touchscreen-max-pressure	General touchscreen binding, see [1].
-	touchscreen-min-pressure	General touchscreen binding, see [1].
-	touchscreen-average-samples	General touchscreen binding, see [1].
-	touchscreen-inverted-x		General touchscreen binding, see [1].
-	touchscreen-inverted-y		General touchscreen binding, see [1].
-	touchscreen-swapped-x-y		General touchscreen binding, see [1].
-
-[1] All general touchscreen properties are described in
-    Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt.
-
-Deprecated properties:
-
-	ti,swap-xy			swap x and y axis
-	ti,x-max			Maximum value on the X axis (u16).
-	ti,y-max			Maximum value on the Y axis (u16).
-	ti,pressure-min			Minimum reported pressure value
-					(threshold) - u16.
-	ti,pressure-max			Maximum reported pressure value (u16).
-	ti,debounce-max			Max number of additional readings per
-					sample (u16).
-
-Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC::
-
-	spi_controller {
-		tsc2046@0 {
-			reg = <0>;	/* CS0 */
-			compatible = "ti,tsc2046";
-			interrupt-parent = <&gpio1>;
-			interrupts = <8 0>;	/* BOOT6 / GPIO 8 */
-			spi-max-frequency = <1000000>;
-			pendown-gpio = <&gpio1 8 0>;
-			vcc-supply = <&reg_vcc3>;
-
-			ti,x-min = /bits/ 16 <0>;
-			ti,x-max = /bits/ 16 <8000>;
-			ti,y-min = /bits/ 16 <0>;
-			ti,y-max = /bits/ 16 <4800>;
-			ti,x-plate-ohms = /bits/ 16 <40>;
-			ti,pressure-max = /bits/ 16 <255>;
-
-			wakeup-source;
-		};
-	};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs7211.yaml b/Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs7211.yaml
index 8cf371b99f19..e4dbbafb3779 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs7211.yaml
+++ b/Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs7211.yaml
@@ -666,7 +666,7 @@ examples:
             #address-cells = <1>;
             #size-cells = <0>;
 
-            touch@56 {
+            touchscreen@56 {
                     compatible = "azoteq,iqs7210a";
                     reg = <0x56>;
                     irq-gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
@@ -704,7 +704,7 @@ examples:
             #address-cells = <1>;
             #size-cells = <0>;
 
-            touch@56 {
+            touchscreen@56 {
                     compatible = "azoteq,iqs7211e";
                     reg = <0x56>;
                     irq-gpios = <&gpio 4 (GPIO_ACTIVE_LOW |
diff --git a/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt
deleted file mode 100644
index ca304357c374..000000000000
--- a/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt
+++ /dev/null
@@ -1,34 +0,0 @@
-* Toradex Colibri VF50 Touchscreen driver
-
-Required Properties:
-- compatible must be toradex,vf50-touchscreen
-- io-channels: adc channels being used by the Colibri VF50 module
-    IIO ADC for Y-, X-, Y+, X+ connections
-- xp-gpios: FET gate driver for input of X+
-- xm-gpios: FET gate driver for input of X-
-- yp-gpios: FET gate driver for input of Y+
-- ym-gpios: FET gate driver for input of Y-
-- interrupts: pen irq interrupt for touch detection, signal from X plate
-- pinctrl-names: "idle", "default"
-- pinctrl-0: pinctrl node for pen/touch detection, pinctrl must provide
-    pull-up resistor on X+, X-.
-- pinctrl-1: pinctrl node for X/Y and pressure measurement (ADC) state pinmux
-- vf50-ts-min-pressure: pressure level at which to stop measuring X/Y values
-
-Example:
-
-	touchctrl: vf50_touchctrl {
-		compatible = "toradex,vf50-touchscreen";
-		io-channels = <&adc1 0>,<&adc0 0>,
-				<&adc0 1>,<&adc1 2>;
-		xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
-		xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
-		yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
-		ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
-		interrupt-parent = <&gpio0>;
-		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
-		pinctrl-names = "idle","default";
-		pinctrl-0 = <&pinctrl_touchctrl_idle>, <&pinctrl_touchctrl_gpios>;
-		pinctrl-1 = <&pinctrl_touchctrl_default>, <&pinctrl_touchctrl_gpios>;
-		vf50-ts-min-pressure = <200>;
-	};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.yaml b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.yaml
index 51d48d4130d3..70a922e213f2 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.yaml
+++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.yaml
@@ -126,7 +126,7 @@ examples:
     i2c {
       #address-cells = <1>;
       #size-cells = <0>;
-      edt-ft5x06@38 {
+      touchscreen@38 {
         compatible = "edt,edt-ft5406";
         reg = <0x38>;
         interrupt-parent = <&gpio2>;
diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.yaml b/Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
index 2a2d86cfd104..eb4992f708b7 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
+++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
@@ -69,7 +69,7 @@ examples:
     i2c {
       #address-cells = <1>;
       #size-cells = <0>;
-      gt928@5d {
+      touchscreen@5d {
         compatible = "goodix,gt928";
         reg = <0x5d>;
         interrupt-parent = <&gpio>;
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti,ads7843.yaml b/Documentation/devicetree/bindings/input/touchscreen/ti,ads7843.yaml
new file mode 100644
index 000000000000..604921733d2c
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/ti,ads7843.yaml
@@ -0,0 +1,183 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/ti,ads7843.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI's SPI driven touch screen controllers
+
+maintainers:
+  - Alexander Stein <alexander.stein@ew.tq-group.com>
+  - Dmitry Torokhov <dmitry.torokhov@gmail.com>
+  - Marek Vasut <marex@denx.de>
+
+description:
+  TI's ADS7843, ADS7845, ADS7846, ADS7873, TSC2046 SPI driven touch screen
+  controllers.
+
+properties:
+  compatible:
+    enum:
+      - ti,ads7843
+      - ti,ads7845
+      - ti,ads7846
+      - ti,ads7873
+      - ti,tsc2046
+
+  interrupts:
+    maxItems: 1
+
+  pendown-gpio:
+    maxItems: 1
+    description:
+      GPIO handle describing the pin the !PENIRQ line is connected to.
+
+  vcc-supply:
+    description:
+      A regulator node for the supply voltage.
+
+  wakeup-source: true
+
+  ti,debounce-max:
+    deprecated: true
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      Max number of additional readings per sample.
+
+  ti,debounce-rep:
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      Additional consecutive good readings required after the first two.
+
+  ti,debounce-tol:
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      Tolerance used for filtering.
+
+  ti,hsync-gpios:
+    maxItems: 1
+    description:
+      GPIO line to poll for hsync.
+
+  ti,keep-vref-on:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Set to keep Vref on for differential measurements as well.
+
+  ti,pendown-gpio-debounce:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Platform specific debounce time for the pendown-gpio.
+
+  ti,penirq-recheck-delay-usecs:
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      If set to non-zero, after samples are taken this delay is applied and
+      penirq is rechecked, to help avoid false events.  This value is
+      affected by the material used to build the touch layer.
+
+  ti,pressure-max:
+    deprecated: true
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      Maximum reported pressure value.
+
+  ti,pressure-min:
+    deprecated: true
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      Minimum reported pressure value (threshold).
+
+  ti,settle-delay-usec:
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      Settling time of the analog signals; a function of Vcc and the
+      capacitance on the X/Y drivers.  If set to non-zero, two samples are
+      taken with settle_delay us apart, and the second one is used. ~150
+      uSec with 0.01uF caps.
+
+  ti,swap-xy:
+    deprecated: true
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Swap x and y axis.
+
+  ti,vref-delay-usecs:
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      Vref supply delay in usecs, 0 for external Vref.
+
+  ti,vref-mv:
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      The VREF voltage, in millivolts.
+      Set to 0 to use internal references (ADS7846).
+
+  ti,x-plate-ohms:
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      Resistance of the X-plate, in Ohms.
+
+  ti,x-max:
+    deprecated: true
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      Maximum value on the X axis.
+
+  ti,x-min:
+    deprecated: true
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      Minimum value on the X axis.
+
+  ti,y-plate-ohms:
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      Resistance of the Y-plate, in Ohms.
+
+  ti,y-max:
+    deprecated: true
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      Maximum value on the Y axis.
+
+  ti,y-min:
+    deprecated: true
+    $ref: /schemas/types.yaml#/definitions/uint16
+    description:
+      Minimum value on the Y axis.
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - $ref: touchscreen.yaml#
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    spi{
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        touchscreen@0 {
+           compatible = "ti,tsc2046";
+           reg = <0>;	/* CS0 */
+           interrupt-parent = <&gpio1>;
+           interrupts = <8 0>;	/* BOOT6 / GPIO 8 */
+           pendown-gpio = <&gpio1 8 0>;
+           spi-max-frequency = <1000000>;
+           vcc-supply = <&reg_vcc3>;
+           wakeup-source;
+
+           ti,pressure-max = /bits/ 16 <255>;
+           ti,x-max = /bits/ 16 <8000>;
+           ti,x-min = /bits/ 16 <0>;
+           ti,x-plate-ohms = /bits/ 16 <40>;
+           ti,y-max = /bits/ 16 <4800>;
+           ti,y-min = /bits/ 16 <0>;
+       };
+    };
diff --git a/Documentation/devicetree/bindings/input/touchscreen/toradex,vf50-touchscreen.yaml b/Documentation/devicetree/bindings/input/touchscreen/toradex,vf50-touchscreen.yaml
new file mode 100644
index 000000000000..5094c5183c74
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/toradex,vf50-touchscreen.yaml
@@ -0,0 +1,77 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/toradex,vf50-touchscreen.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Toradex Colibri VF50 Touchscreen
+
+maintainers:
+  - Dmitry Torokhov <dmitry.torokhov@gmail.com>
+  - Sanchayan Maity <maitysanchayan@gmail.com>
+
+properties:
+  compatible:
+    const: toradex,vf50-touchscreen
+
+  interrupts:
+    maxItems: 1
+
+  io-channels:
+    maxItems: 4
+    description:
+      adc channels being used by the Colibri VF50 module
+      IIO ADC for Y-, X-, Y+, X+ connections
+
+  xp-gpios:
+    description: FET gate driver for input of X+
+
+  xm-gpios:
+    description: FET gate driver for input of X-
+
+  yp-gpios:
+    description: FET gate driver for input of Y+
+
+  ym-gpios:
+    description: FET gate driver for input of Y-
+
+  vf50-ts-min-pressure:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 50
+    maximum: 2000
+    description: pressure level at which to stop measuring X/Y values
+
+required:
+  - compatible
+  - io-channels
+  - xp-gpios
+  - xm-gpios
+  - yp-gpios
+  - ym-gpios
+  - interrupts
+  - vf50-ts-min-pressure
+
+allOf:
+  - $ref: touchscreen.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    touchscreen {
+        compatible = "toradex,vf50-touchscreen";
+        interrupt-parent = <&gpio0>;
+        interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+        io-channels = <&adc1 0>, <&adc0 0>, <&adc0 1>, <&adc1 2>;
+        xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+        xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+        yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+        ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+        pinctrl-names = "idle", "default";
+        pinctrl-0 = <&pinctrl_touchctrl_idle>, <&pinctrl_touchctrl_gpios>;
+        pinctrl-1 = <&pinctrl_touchctrl_default>, <&pinctrl_touchctrl_gpios>;
+        vf50-ts-min-pressure = <200>;
+    };
diff --git a/Documentation/devicetree/bindings/input/touchscreen/zinitix,bt400.yaml b/Documentation/devicetree/bindings/input/touchscreen/zinitix,bt400.yaml
index b1507463a03e..3f663ce3e44e 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/zinitix,bt400.yaml
+++ b/Documentation/devicetree/bindings/input/touchscreen/zinitix,bt400.yaml
@@ -16,6 +16,7 @@ maintainers:
 
 allOf:
   - $ref: touchscreen.yaml#
+  - $ref: ../input.yaml#
 
 properties:
   $nodename:
@@ -79,6 +80,15 @@ properties:
     $ref: /schemas/types.yaml#/definitions/uint32
     enum: [1, 2]
 
+  linux,keycodes:
+    description:
+      This property specifies an array of keycodes assigned to the
+      touch-keys that can be present in some touchscreen configurations.
+      If the touch-keys are enabled, controller firmware will assign some
+      touch sense lines to those keys.
+    minItems: 1
+    maxItems: 8
+
   touchscreen-size-x: true
   touchscreen-size-y: true
   touchscreen-fuzz-x: true
diff --git a/Documentation/devicetree/bindings/power/wakeup-source.txt b/Documentation/devicetree/bindings/power/wakeup-source.txt
index 128b55be67b7..27f1797be963 100644
--- a/Documentation/devicetree/bindings/power/wakeup-source.txt
+++ b/Documentation/devicetree/bindings/power/wakeup-source.txt
@@ -25,7 +25,7 @@ List of legacy properties and respective binding document
 2. "has-tpo"			Documentation/devicetree/bindings/rtc/rtc-opal.txt
 3. "linux,wakeup"		Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt
 				Documentation/devicetree/bindings/mfd/tc3589x.txt
-				Documentation/devicetree/bindings/input/touchscreen/ads7846.txt
+				Documentation/devicetree/bindings/input/touchscreen/ti,ads7843.yaml
 4. "linux,keypad-wakeup"	Documentation/devicetree/bindings/input/qcom,pm8921-keypad.yaml
 5. "linux,input-wakeup"		Documentation/devicetree/bindings/input/samsung,s3c6410-keypad.yaml
 6. "nvidia,wakeup-source"	Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt