| Age | Commit message (Collapse) | Author |
|---|
|
Add byte queue limits support in the fsl_ucc_hdlc driver.
Signed-off-by: Mathias Thore <mathias.thore@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of listing every single PHYID, load the driver for every PHYID
with a Realtek OUI, independent of model number and revision.
This patch also improves two further aspects:
- constify realtek_tbl[]
- the mask should have been 0xffffffff instead of 0x001fffff so far,
by masking out some bits a PHY from another vendor could have been
matched
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_trigger_machine() is used in phy.c only, so we can make it static.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/dsa/bcm_sf2_cfp.c:1168:2-3: Unneeded semicolon
drivers/net/dsa/bcm_sf2_cfp.c:532:2-3: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Fixes: ae7a5aff783c ("net: dsa: bcm_sf2: Keep copy of inserted rules")
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for BCM7255 EPHY.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb for packets that are multicast or to a link-local address are
not marked as being enslaved to a VRF, if they are received on a socket
bound to the VRF. This is needed for ND and it is preferable for the
kernel not to have to deal with the additional use-cases if ll or mcast
packets are handled as enslaved. However, this does not allow service
instances listening on unbound and bound to VRF sockets to distinguish
the VRF used, if packets are sent as multicast or to a link-local
address. The fix is for the VRF driver to also mark these skb as being
enslaved to the VRF.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c: In function 'hclge_log_and_clear_ppp_error':
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c:821:24: warning:
variable 'reset_level' set but not used [-Wunused-but-set-variable]
enum hnae3_reset_type reset_level = HNAE3_NONE_RESET;
It never used since introduction in commit
01865a50d78f ("net: hns3: Add enable and process hw errors of TM scheduler")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use driver's common notifier for LAG and tunnel configuration.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code interested in networking events registers its own notifier
handlers. Create one device-wide notifier instance.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nfp_fl_lag_changels_event() never fails, and therefore we would
never return NOTIFY_BAD for NETDEV_CHANGELOWERSTATE. Make this
clearer by changing nfp_fl_lag_changels_event()'s return type
to void.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Returning an error from a notifier means we want to veto the change.
We shouldn't veto NETDEV_UNREGISTER just because we couldn't find
the tracking info for given master.
I can't seem to find a way to trigger this unless we have some
other bug, so it's probably not fix-worthy.
While at it move the checking if the netdev really is of interest
into the handling functions, like we do for other events.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For flower tunnel offloads FW has to be informed about MAC addresses
of tunnel devices. We use a netdev notifier to keep track of these
addresses.
Remove unnecessary loop over netdevices after notifier is registered.
The intention of the loop was to catch devices which already existed
on the system before nfp driver got loaded, but netdev notifier will
replay NETDEV_REGISTER events.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ipv6 set flow label and hop limit action offload. Since pedit sets
headers per 4 byte word, we need to ensure that setting either version,
priority, payload_len or nexthdr does not get offloaded.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ipv4 set ttl and tos action offload. Since pedit sets headers per 4
byte word, we need to ensure that setting either version, ihl, protocol,
total length or checksum does not get offloaded.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is not necessary to reallocate the descriptor and remap the
descriptor memory in reset process, otherwise it may cause memory
not freed problem.
Also, this patch initializes the cmd queue's spinlocks in
hclgevf_alloc_cmd_queue, and take the spinlocks when reinitializing
cmd queue' registers.
Fixes: fedd0c15d288 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When hclge_reset() is called, it may fail for several reasons.
For example, an higher-level reset event occurs, memory allocation
failure, hardware reset timeout, etc. Therefore, it is necessary
to add corresponding error handling for these situations.
1. A high-level reset is required due to a high-level reset failure.
2. For memory allocation failure, a high-level reset is initiated by
the timer to recover. The reason for using the timer is to prevent this
new high-level reset to interrupt the reset process of other pf/vf;
3. For the case of hardware reset timeout, reschedule the reset task
to wait for the hardware to complete the reset.
For memory allocation failure and reset timeouts, in order to prevent
an infinite number of scheduled reset tasks, the number of error
recovery needs to be limited.
This patch also add some reset related debug log printing.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While doing resetting, roce should do its uninitailization part
before nic's, and do its initialization part after nic's.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing PF reset, the driver needs to do some preparatory work
before asserting PF reset. Since when hardware is resetting, it
is necessary to stop tx/rx queue, clear hardware table, etc,
otherwise hardware may run into unrecoverable state if there is
still IO running when the hardware is resetting.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hclge_dev/hclgevf_dev
Saving reset related information in the hclge_dev/hclgevf_dev
structure is more suitable than the hnae3_handle, since hardware
related information is kept in these two structure.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When processing a higher level reset, the pending lower level reset
does not have to be processed anymore, because the higher level
reset is the superset of the lower level reset.
Therefore, when processing an higher level reset, the request of
lower level reset needs to be cleared.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While hclge is going to reset, it will notify its client with
HNAE3_DOWN_CLIENT, so this client should get into a resetting
status from this moment, other operations from the stack need to
be blocked as well. And when the reset is finished, the client
will be notified with HNAE3_UP_CLIENT, so this is the end of
the resetting status.
This patch uses HNS3_NIC_STATE_RESETTING flag to implement that,
and adds hns3_nic_resetting() to indicate which operation is not
allowed.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While hardware gets into reset status, the firmware will not respond to
driver's command request, which may cause ring not disabled problem
during reset process.
So this patch uses register instead of command to enable/disable the ring
in the enet while doing UP/DOWN operation.
Also, HNS3_RING_RX_VM_REG is previously unused, so change it to the
correct meaning, and add a wrapper function for readl().
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing a function reset, the hardware table should be cleared
before the hardware reset. In current code, this clearing is done
in hns3_reset_notify_uninit_enet, but it is too late, because
the hardware reset is already done, hns3_reset_notify_down_enet
is more suitable to do that.
Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The client needs to know if the hardware is resetting when
loading or unloading itself, because client may abort the loading
process or wait for the reset process to finish when unloading
if hardware is resetting.
So this patch provides these interfaces to do it.
1. get_hw_reset_stat, the reset status of hardware.
2. ae_dev_resetting, whether reset task is scheduling.
3. ae_dev_reset_cnt, how many reset has been done.
Also, the RoCE client needs some field in the hnae3_roce_private_info
to save its state, and process_hw_error interface in the
hnae3_client_ops to process hardware errors.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when reset_event is called because of tx timeout, it will
upgrade the reset level (For PF, HNAE3_FUNC_RESET -> HNAE3_CORE_RESET
-> HNAE3_GLOBAL_RESET) if the time between the new reset and last reset
is within 20 secs, or restore the reset level to HNAE3_FUNC_RESET if
the time between the new reset and last reset is over 20 secs.
There is requirement that the caller needs to decide the reset level
when triggering a reset, for example, RAS recovery. So this patch
adds the set_default_reset_request to meet this requirement.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
enet
Besides of module_init and module_exit, the process of reset will
also uninitialize and initialize the enet client. When reset process
fails with enet client uninitialized, the module_exit does not need
to uninitialize the enet client, otherwise it may cause double
uninitialization problem.
So we need the HNS3_NIC_STATE_INITED flag to indicate whether
the enet client is initialized.
Also HNS3_NIC_STATE_REINITING is previously unused, so change it to
HNS3_NIC_STATE_INITED.
Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Binding and unbinding the switch driver which creates the DSA slave
network devices for which we set-up inspection would lead to
undesireable effects since we were not clearing the port/queue mapping
to the SYSTEMPORT TX queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The use of a bitmap speeds up the finding of the first available queue
to which we could start establishing the mapping for, but we still have
to loop over all slave network devices to set them up. Simplify the
logic to have a single loop, and use the fact that a correctly
configured ring has inspect set to true. This will make things simpler
to unwind during device unregistration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are binding to the PHY using the SF2 slave MDIO bus that we create,
binding involves reading the PHY's MII_PHYSID1/2 which won't be possible
if the PHY is turned off. Temporarily turn it on/off for the bus probing
to succeeed. This fixes unbind/bind problems where the port connecting
to that PHY would be in error since it could not connect to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the system suspend states that we support wipe out entirely the
HW contents. If we had a Wake-on-LAN filter programmed prior to going
into suspend, but we did not actually wake-up from Wake-on-LAN and
instead used a deeper suspend state, make sure we restore the CID number
that we need to match against.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have migrated the CFP rule handling to a list with a
software copy, the delete/get operation just returns what is on the
list, no need to read from the hardware which is both slow and more
error prone.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware can lose its context during system suspend, and depending
on the switch generation (7445 vs. 7278), while the rules are still
there, they will have their valid bit cleared (because that's the
fastest way for the HW to reset things). Just make sure we re-apply them
coming back from resume. The 7445 switch is an older version of the core
that has some quirky RAM technology requiring a delete then re-inser to
guarantee the RAM entries are properly latched.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for restoring CFP rules during system wide system
suspend/resume where the hardware loses its context, split the rule
validation from its actual insertion as well as the rule removal from
its actual hardware deletion operation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We tried hard to use the hardware as a storage area, which made things
needlessly complex in that we had to both marshall and unmarshall the
ethtool_rx_flow_spec into what the CFP hardware understands but it did
not require any driver level allocations, so that was nice.
Keep a copy of the ethtool_rx_flow_spec rule we want to insert, and also
make sure we don't have a duplicate rule already. This greatly speeds up
the deletion time since we only need to clear the slice's valid bit and
not perform a full read.
This is a preparatory step for being able to restore rules upon system
resumption where the hardware loses its context partially or entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add extack arg to rtnl_create_link and add messages for invalid
number of Tx or Rx queues.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I started looking at the history of this driver, and last time the
maintainer was active on the mailing list was when discussing how to
remove it. This was in 2012:
https://lore.kernel.org/lkml/4F4DE175.30002@melware.de/
It looks to me like this has in practice been an orphan for quite a while.
It's throwing warnings about stack size in a function that is in dire
need of refactoring, and it's probably a case of "it's time to call it".
Cc: Armin Schindler <mac@melware.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Handle errors mid-stream of an all dump, from Alexey Kodanev.
2) Fix build of openvswitch with certain combinations of netfilter
options, from Arnd Bergmann.
3) Fix interactions between GSO and BQL, from Eric Dumazet.
4) Don't put a '/' in RTL8201F's sysfs file name, from Holger
Hoffstätte.
5) S390 qeth driver fixes from Julian Wiedmann.
6) Allow ipv6 link local addresses for netconsole when both source and
destination are link local, from Matwey V. Kornilov.
7) Fix the BPF program address seen in /proc/kallsyms, from Song Liu.
8) Initialize mutex before use in dsa microchip driver, from Tristram
Ha.
9) Out-of-bounds access in hns3, from Yunsheng Lin.
10) Various netfilter fixes from Stefano Brivio, Jozsef Kadlecsik, Jiri
Slaby, Florian Westphal, Eric Westbrook, Andrey Ryabinin, and Pablo
Neira Ayuso.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (50 commits)
net: alx: make alx_drv_name static
net: bpfilter: fix iptables failure if bpfilter_umh is disabled
sock_diag: fix autoloading of the raw_diag module
net: core: netpoll: Enable netconsole IPv6 link local address
ipv6: properly check return value in inet6_dump_all()
rtnetlink: restore handling of dumpit return value in rtnl_dump_all()
net/ipv6: Move anycast init/cleanup functions out of CONFIG_PROC_FS
bonding/802.3ad: fix link_failure_count tracking
net: phy: realtek: fix RTL8201F sysfs name
sctp: define SCTP_SS_DEFAULT for Stream schedulers
sctp: fix strchange_flags name for Stream Change Event
mlxsw: spectrum: Fix IP2ME CPU policer configuration
openvswitch: fix linking without CONFIG_NF_CONNTRACK_LABELS
qed: fix link config error handling
net: hns3: Fix for out-of-bounds access when setting pfc back pressure
net/mlx4_en: use __netdev_tx_sent_queue()
net: do not abort bulk send on BQL status
net: bql: add __netdev_tx_sent_queue()
s390/qeth: report 25Gbit link speed
s390/qeth: sanitize ARP requests
...
|
|
alx_drv_name is not used outside main.c, so there's no reason for it to
have external linkage.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4d2c0cda07448ea6980f00102dc3964eb25e241c set slave->link to
BOND_LINK_DOWN for 802.3ad bonds whenever invalid speed/duplex values
were read, to fix a problem with slaves getting into weird states, but
in the process, broke tracking of link failures, as going straight to
BOND_LINK_DOWN when a link is indeed down (cable pulled, switch rebooted)
means we broke out of bond_miimon_inspect()'s BOND_LINK_DOWN case because
!link_state was already true, we never incremented commit, and never got
a chance to call bond_miimon_commit(), where slave->link_failure_count
would be incremented. I believe the simple fix here is to mark the slave
as BOND_LINK_FAIL, and let bond_miimon_inspect() transition the link from
_FAIL to either _UP or _DOWN, and in the latter case, we now get proper
incrementing of link_failure_count again.
Fixes: 4d2c0cda0744 ("bonding: speed/duplex update at NETDEV_UP event")
CC: Mahesh Bandewar <maheshb@google.com>
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:
$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]
Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd44b ("net: phy: realtek: add RTL8201F phy-id and functions").
Fix this by removing the offending slash in the driver name.
Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.
Fixes: 513588dd44b ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull UBIFS updates from Richard Weinberger:
- Full filesystem authentication feature, UBIFS is now able to have the
whole filesystem structure authenticated plus user data encrypted and
authenticated.
- Minor cleanups
* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
ubifs: Remove unneeded semicolon
Documentation: ubifs: Add authentication whitepaper
ubifs: Enable authentication support
ubifs: Do not update inode size in-place in authenticated mode
ubifs: Add hashes and HMACs to default filesystem
ubifs: authentication: Authenticate super block node
ubifs: Create hash for default LPT
ubfis: authentication: Authenticate master node
ubifs: authentication: Authenticate LPT
ubifs: Authenticate replayed journal
ubifs: Add auth nodes to garbage collector journal head
ubifs: Add authentication nodes to journal
ubifs: authentication: Add hashes to index nodes
ubifs: Add hashes to the tree node cache
ubifs: Create functions to embed a HMAC in a node
ubifs: Add helper functions for authentication support
ubifs: Add separate functions to init/crc a node
ubifs: Format changes for authentication support
ubifs: Store read superblock node
ubifs: Drop write_node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more timer updates from Thomas Gleixner:
"A set of commits for the new C-SKY architecture timers"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dt-bindings: timer: gx6605s SOC timer
clocksource/drivers/c-sky: Add gx6605s SOC system timer
dt-bindings: timer: C-SKY Multi-processor timer
clocksource/drivers/c-sky: Add C-SKY SMP timer
|
|
Pull NTB updates from Jon Mason:
"Fairly minor changes and bug fixes:
NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
private struct, and a few bug fixes"
* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
ntb: idt: Alter the driver info comments
ntb: idt: Discard temperature sensor IRQ handler
ntb: idt: Add basic hwmon sysfs interface
ntb: idt: Alter temperature read method
ntb_netdev: Simplify remove with client device drvdata
NTB: transport: Try harder to alloc an aligned MW buffer
ntb: ntb_transport: Mark expected switch fall-throughs
ntb: idt: Set PCIe bus address to BARLIMITx
NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
ntb: intel: fix return value for ndev_vec_mask()
ntb_netdev: fix sleep time mismatch
|
|
The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.
Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.
Fixes: 9148e7cf73ce ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:
drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.
Fixes: c56a8be7e7aa ("qed: Add supported link and advertise link to display in ethtool.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A number of fixes and some late updates:
- make in_compat_syscall() behavior on x86-32 similar to other
platforms, this touches a number of generic files but is not
intended to impact non-x86 platforms.
- objtool fixes
- PAT preemption fix
- paravirt fixes/cleanups
- cpufeatures updates for new instructions
- earlyprintk quirk
- make microcode version in sysfs world-readable (it is already
world-readable in procfs)
- minor cleanups and fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compat: Cleanup in_compat_syscall() callers
x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
objtool: Support GCC 9 cold subfunction naming scheme
x86/numa_emulation: Fix uniform-split numa emulation
x86/paravirt: Remove unused _paravirt_ident_32
x86/mm/pat: Disable preemption around __flush_tlb_all()
x86/paravirt: Remove GPL from pv_ops export
x86/traps: Use format string with panic() call
x86: Clean up 'sizeof x' => 'sizeof(x)'
x86/cpufeatures: Enumerate MOVDIR64B instruction
x86/cpufeatures: Enumerate MOVDIRI instruction
x86/earlyprintk: Add a force option for pciserial device
objtool: Support per-function rodata sections
x86/microcode: Make revision and processor flags world-readable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"An irqchip driver fix and a memory (over-)allocation fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-mvebu-sei: Fix a NULL vs IS_ERR() bug in probe function
irq/matrix: Fix memory overallocation
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.
[ 35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14
[ 35.254132] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.19.0-rc7-hulk+ #85
[ 35.254133] Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI RC0 - B052 (V0.52) 09/14/2018
[ 35.254141] Workqueue: events work_for_cpu_fn
[ 35.254144] Call trace:
[ 35.254147] dump_backtrace+0x0/0x2f0
[ 35.254149] show_stack+0x24/0x30
[ 35.254154] dump_stack+0x110/0x184
[ 35.254157] print_address_description+0x168/0x2b0
[ 35.254160] kasan_report+0x184/0x310
[ 35.254162] __asan_load2+0x7c/0xa0
[ 35.254170] hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254177] hclge_tm_init_hw+0x794/0x9f0 [hclge]
[ 35.254184] hclge_tm_schd_init+0x48/0x58 [hclge]
[ 35.254191] hclge_init_ae_dev+0x778/0x1168 [hclge]
[ 35.254196] hnae3_register_ae_dev+0x14c/0x298 [hnae3]
[ 35.254206] hns3_probe+0x88/0xa8 [hns3]
[ 35.254210] local_pci_probe+0x7c/0xf0
[ 35.254212] work_for_cpu_fn+0x34/0x50
[ 35.254214] process_one_work+0x4d4/0xa38
[ 35.254216] worker_thread+0x55c/0x8d8
[ 35.254219] kthread+0x1b0/0x1b8
[ 35.254222] ret_from_fork+0x10/0x1c
[ 35.254224] The buggy address belongs to the page:
[ 35.254228] page:ffff7e00ed994400 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[ 35.273835] flags: 0xfffff8000008000(head)
[ 35.282007] raw: 0fffff8000008000 dead000000000100 dead000000000200 0000000000000000
[ 35.282010] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[ 35.282012] page dumped because: kasan: bad access detected
[ 35.282014] Memory state around the buggy address:
[ 35.282017] ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282019] ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282022] ^
[ 35.282024] ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282026] ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282028] ==================================================================
[ 35.282029] Disabling lock debugging due to kernel taint
[ 35.282747] hclge driver initialization finished.
Fixes: 67bf2541f4b9 ("net: hns3: Fixes the back pressure setting when sriov is enabled")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
doorbell only depends on xmit_more and netif_tx_queue_stopped()
Using __netdev_tx_sent_queue() avoids messing with BQL stop flag,
and is more generic.
This patch increases performance on GSO workload by keeping
doorbells to the minimum required.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
