| Age | Commit message (Collapse) | Author |
|---|
|
The existing genphy_loopback() is not working for TI DP83867 PHY as it
will disable autoneg support while another side is still enabling autoneg.
This is causing the link is not established and results in timeout error
in genphy_loopback() function.
Thus, based on TI PHY datasheet, introduce a TI PHY loopback function by
just configuring BMCR_LOOPBACK(Bit-9) in MII_BMCR register (0x0).
Tested working on TI DP83867 PHY for all speeds (10/100/1000Mbps).
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221108101527.612723-1-michael.wei.hong.sit@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support to SGMII register dump
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the unused argument (i.e. struct ethtool_regs *regs) in
lan743x_common_regs( ) function arguments.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add locked bridge port support by reacting to changes in the
'BR_PORT_LOCKED' flag. When set, enable security checks on the local
port via the previously added SPFSR register.
When security checks are enabled, an incoming packet will trigger an FDB
lookup with the packet's source MAC and the FID it was classified to. If
an FDB entry was not found or was found to be pointing to a different
port, the packet will be dropped. Such packets increment the
"discard_ingress_general" ethtool counter. For added visibility, user
space can trap such packets to the CPU by enabling the "locked_port"
trap. Example:
# devlink trap set pci/0000:06:00.0 trap locked_port action trap
Unlike other configurations done via bridge port flags (e.g., learning,
flooding), security checks are enabled in the device on a per-port basis
and not on a per-{port, VLAN} basis. As such, scenarios where user space
can configure different locking settings for different VLANs configured
on a port need to be vetoed. To that end, veto the following scenarios:
1. Locking is set on a bridge port that is a VLAN upper
2. Locking is set on a bridge port that has VLAN uppers
3. VLAN upper is configured on a locked bridge port
Examples:
# bridge link set dev swp1.10 locked on
Error: mlxsw_spectrum: Locked flag cannot be set on a VLAN upper.
# ip link add link swp1 name swp1.10 type vlan id 10
# bridge link set dev swp1 locked on
Error: mlxsw_spectrum: Locked flag cannot be set on a bridge port that has VLAN uppers.
# bridge link set dev swp1 locked on
# ip link add link swp1 name swp1.10 type vlan id 10
Error: mlxsw_spectrum: VLAN uppers are not supported on a locked port.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Propagate extack to mlxsw_sp_port_attr_br_pre_flags_set() in order to
communicate error messages related to bridge port flag validation.
Example:
# bridge link set dev swp1 locked on
Error: mlxsw_spectrum: Unsupported bridge port flag.
More error messages will be added in subsequent patches.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In Spectrum, learning happens in parallel to the security checks.
Therefore, regardless of the result of the security checks, a learning
notification will be generated by the device and polled later on by the
driver.
Currently, the driver reacts to learning notifications by programming
corresponding FDB entries to the device. When a port is locked (i.e.,
has security checks enabled), this can no longer happen, as otherwise
any host will blindly gain authorization.
Instead, notify the learned entry as a locked entry to the bridge driver
that will in turn notify it to user space, in case MAB is enabled. User
space can then decide to authorize the host by clearing the "locked"
flag, which will cause the entry to be programmed to the device.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Subsequent patches will need to report locked FDB entries to the bridge
driver. Prepare for that by adding a 'locked' argument to
mlxsw_sp_fdb_call_notifiers() according to which the 'locked' bit is set
in the FDB notification info. For now, always pass 'false'.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add an API to enable or disable security checks on a local port. It will
be used by subsequent patches when the 'BR_PORT_LOCKED' flag is toggled.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the Switch Port FDB Security Register (SPFSR) that allows enabling
and disabling security checks on a given local port. In Linux terms, it
allows locking / unlocking a port.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Register the previously added packet traps with devlink. This allows
user space to tune their policers and in the case of the locked port
trap, user space can set its action to "trap" in order to gain
visibility into packets that were discarded by the device due to the
locked port check failure.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Probe functions uses normal dev_err() to check error conditions
and print messages. Replace dev_err() with dev_err_probe() to
have more standardized format and error logging.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ8563 have three port interrupts: PTP, PHY and ACL. Add
port_nirq as 3 for KSZ8563 inside ksz_chip_data.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add status validation for port register write inside
lan937x_change_mtu. ksz_pwrite and ksz_pread api's are
updated with return type int (Reference patch mentioned
below). Update lan937x_change_mtu with status validation
for ksz_pwrite16().
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220826105634.3855578-6-o.rempel@pengutronix.de/
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add device irq in i2c probe function.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
compatible string
Add KSZ9563 inside ksz_switch_chips structure with
port_nirq as 3. KSZ9563 use KSZ9893 switch parameters
but port_nirq count is 3 for KSZ9563 whereas 2 for
KSZ9893. Add KSZ9563 inside ksz_switch_chips as a separate
member and from device tree map compatible string into
KSZ9563 inside ksz_spi.c and ksz9477_i2c.c.
Global Chip ID 1 and 2 registers read value 9893, select
sku based on Global Chip ID 4 Register which read 0x1c
for KSZ9563.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Coverity reported that the error path in rswitch_gwca_queue_alloc_skb()
has an issue to cause endless loop. So, fix the issue by changing
variables' types from u32 to int. After changed the types,
rswitch_tx_free() should use rswitch_get_num_cur_queues() to
calculate number of current queues.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1527147 ("Control flow issues")
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20221107081021.2955122-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When using a PHC that is shared between multiple hosts,
in order to achieve consistent timestamps across all hosts,
we need to isolate the PHC from any host making frequency
adjustments.
This patch adds a non-real time mode for this purpose.
The implementation is based on a free running NIC hardware timer
which is used as the timestamper time-base. Each host implements
individual adjustments to a local timecounter based on the NIC free
running timer.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Hardware is unable to realize all legal firmware interface state values
for hash_type. For example, if 4-tuple TCP_IPV4 hash is enabled,
4-tuple UDP_IPV4 hash must also be enabled. By providing the bits the
user intended to change instead of the possible illegal intermediate
states, the firmware is able to make better compromises when deciding
which bits to ignore.
With this new mechansim, we can now report the actual configured hash
back to the user. Add bnxt_hwrm_update_rss_hash_cfg() to report the
actual hash after user configuration.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Extract common code into a new function. This will avoid duplication
in the next patch, which changes the update algorithm for both the P5
and legacy code paths.
No functional changes.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The previous attempt to augment carrier_down (see Link)
was not met with much enthusiasm so let's do the simple
thing of exposing what some devices already maintain.
Add a common ethtool statistic for link going down.
Currently users have to maintain per-driver mapping
to extract the right stat from the vendor-specific ethtool -S
stats. carrier_down does not fit the bill because it counts
a lot of software related false positives.
Add the statistic to the extended link state API to steer
vendors towards implementing all of it.
Implement for bnxt and all Linux-controlled PHYs. mlx5 and (possibly)
enic also have a counter for this but I leave the implementation
to their maintainers.
Link: https://lore.kernel.org/r/20220520004500.2250674-1-kuba@kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20221104190125.684910-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The error checks on checksum for a negative error return always fails because
it is unsigned and can never be negative.
Fixes: 049fe5365324 ("net: txgbe: Add operations to interact with firmware")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
eeprom_ptrs should be freed before returned.
Fixes: 049fe5365324 ("net: txgbe: Add operations to interact with firmware")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-11-04 (ixgbe, ixgbevf, igb)
This series contains updates to ixgbe, ixgbevf, and igb drivers.
Daniel Willenson adjusts descriptor buffer limits to be based on what
hardware supports instead of using a generic, least common value for
ixgbe.
Ani removes local variable for ixgbe, instead returning conditional result
directly.
Yang Li removes unneeded semicolon for ixgbe.
Jan adds error messaging when VLAN errors are encountered for ixgbevf.
Kees Cook prevents a potential use after free condition and explicitly
rounds up q_vector allocations so that allocations can be correctly
compared to ksize() for igb.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igb: Proactively round up to kmalloc bucket size
igb: Do not free q_vector unless new one was allocated
ixgbevf: Add error messages on vlan error
ixgbe: Remove unneeded semicolon
ixgbe: Remove local variable
ixgbe: change MAX_RXD/MAX_TXD based on adapter type
====================
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221104205414.2354973-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement live mac addr change for the macb ethernet driver.
Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221104204837.614459-1-roman.gushchin@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Virtually all conventional network drivers are now converted to use
phylink_generic_validate() - only DSA drivers and fman_memac remain,
so lets remove the necessity for network drivers to explicitly set
this member, and default to phylink_generic_validate() when unset.
This is possible as .validate must currently be set.
Any remaining instances that have not been addressed by this patch can
be fixed up later.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/E1or0FZ-001tRa-DI@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
lan966x_phylink.c doesn't make use of anything from linux/sfp.h, so
remove this unnecessary include.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1oqzx9-001r9g-HV@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On low power during system suspend the ALE table context is lost.
Save the ALE contect before suspend and restore it after resume.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During suspend resume the context of PORT_VLAN_REG is lost so
save it during suspend and restore it during resume for
host port and slave ports.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This can be used by device driver to restore ALE context.
The data produced by cpsw_ale_dump() can be passed to
cpsw_ale_restore().
This is required as on certain platforms the ALE context
is lost on low power suspend/resume.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add PM handlers for System suspend/resume.
As DMA driver doesn't yet support suspend/resume we free up
the DMA channels at suspend and acquire and initialize them
at resume.
Move the init/free dma calls to ndo_open/close() hooks so
it is symmetric and easier to invoke from suspend/resume handler.
As CPTS looses contect during suspend/resume, invoke the
necessary CPTS suspend/resume helpers.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CPTS looses context on suspend (e.g. on AM62).
Provide suspend/resume hooks in CPTS driver. These will be
invoked by CPSW driver if CPTS was instantiated by CPSW.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cocci warnings: (new ones prefixed by >>)
>> drivers/net/phy/motorcomm.c:1122:8-35: duplicated argument to & or |
drivers/net/phy/motorcomm.c:1126:8-35: duplicated argument to & or |
drivers/net/phy/motorcomm.c:1130:8-34: duplicated argument to & or |
drivers/net/phy/motorcomm.c:1134:8-34: duplicated argument to & or |
The second YT8521_RC1R_GE_TX_DELAY_xx should be YT8521_RC1R_FE_TX_DELAY_xx.
Fixes: 70479a40954c ("net: phy: Add driver for Motorcomm yt8521 gigabit ethernet phy")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Frank <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If alloc_page() fails in gve_prefill_rx_pages(), it should return
an error code in the error path.
Fixes: 82fd151d38d9 ("gve: Reduce alloc and copy costs in the GQ rx path")
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Catherine Sullivan <csully@google.com>
Cc: Shailend Chand <shailend@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the code logic of handling the quirk of FEC_QUIRK_HAS_RACC.
If a SoC has the RACC quirk, the driver will enable the 16bit shift
by default in the probe function for a better performance.
This patch handles the logic in one place to make the logic simple
and clean. The patch optimizes the fec_enet_xdp_get_tx_queue function
according to Paolo Abeni's comments, and it also exludes the SoCs that
require to do frame swap from XDP support.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/lcs.c:2090:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
drivers/s390/net/lcs.c:2097:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of lcs_start_xmit() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/netiucv.c:1854:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = netiucv_tx,
^~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of netiucv_tx() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Additionally, while in the area, remove a comment block that is no
longer relevant.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/ctcm_main.c:1064:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = ctcm_tx,
^~~~~~~
drivers/s390/net/ctcm_main.c:1072:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = ctcmpc_tx,
^~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of ctc{mp,}m_tx() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Additionally, while in the area, remove a comment block that is no
longer relevant.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the work queue based RX flow with a NAPI implementation
Remove rx_thread and dpmaif_rxq_work.
Enable GRO on RX path.
Introduce dummy network device. its responsibility is
- Binds one NAPI object for each DL HW queue and acts as
the agent of all those network devices.
- Use NAPI object to poll DL packets.
- Helps to dispatch each packet to the network interface.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Co-developed-by: Sreehari Kancharla <sreehari.kancharla@linux.intel.com>
Signed-off-by: Sreehari Kancharla <sreehari.kancharla@linux.intel.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Acked-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Acked-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hard_header_len is used by gro_list_prepare() but on Rx, there
is no header so use needed_headroom instead.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sreehari Kancharla <sreehari.kancharla@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ethtool config rx-vlan-filter, the driver will send
control command to firmware, then set to hardware in this patch.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HINIC has a mailbox for PF-VF communication and the VF driver
could send port control command to PF driver via mailbox.
The control command only can be set to register in PF,
so add support in PF driver for VF PMD driver control
command when VF PMD driver work with linux PF driver.
Then, no need to add handlers to nic_vf_cmd_msg_handler[],
because the host driver just forwards it to the firmware.
Actually the firmware works on a coprocessor MGMT_CPU(inside the NIC)
which will recv and deal with these commands.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The print cmd code is in hex, so using hex cmd code intead of
decimal is easy to check the value with print info.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support basic system-wide suspend and resume functions
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support mode switch properly, which is not available before.
If SoC has two Ethernet controllers, by setting both of them into MII
mode, the first controller enters GMII mode, while the second
controller is effectively disabled. This requires configuring (and
maybe enabling) the second controller in the device tree, even though
it cannot be used.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for Octeon device CNF95N.
CNF95N is a Octeon Fusion family product with same PCI NIC
characteristics as CN93 which is currently supported by the driver.
update supported device list in Documentation.
Signed-off-by: Veerasenareddy Burru <vburru@marvell.com>
Link: https://lore.kernel.org/r/20221103060600.1858-1-vburru@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support matching on UDP/TCP source and destination ports and TCP flags,
with masking if supported by the hardware.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support matching on ip_frag and ip_firstfrag.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support matching on IP protocol, Type of Service, Time To Live, source
and destination addresses, with masking if supported by the hardware.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support matching on EtherType, VLANs and ethernet source/destination
addresses, with masking if supported by the hardware.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Offloaded TC rules always match on recirc_id in the MAE, so we should
check that the MAE reported support for this match before attempting
to insert the rule.
These checks allow us to fail early, avoiding the PCIe round-trip to
firmware for an MC_CMD_MAE_ACTION_RULE_INSERT that will only fail,
and more importantly providing a more informative error message that
identifies which match field is unsupported.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
