| Age | Commit message (Collapse) | Author |
|---|
|
Map read has been supported on NFP, this patch enables optimization
for memcpy from map to packet.
This patch also fixed one latent bug which will cause copying from
unexpected address once memcpy for map pointer enabled. The fixed
code path was not exercised before.
Reported-by: Mary Pham <mary.pham@netronome.com>
Reported-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
In the quest to remove all stack VLA usage from the kernel[1], this
allocates the values buffer during the callback instead of putting it
on the stack.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call the reoffload tcf_proto_op on all tcf_proto nodes in all chains of a
block when a callback tries to register to a block that already has
offloaded rules. If all existing rules cannot be offloaded then the
registration is rejected. This replaces the previous policy of rejecting
such callback registration outright.
On unregistration of a callback, the rules are flushed for that given cb.
The implementation of block sharing in the NFP driver, for example,
duplicates shared rules to all devs bound to a block. This meant that
rules could still exist in hw even after a device is unbound from a block
(assuming the block still remains active).
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass the extact struct from a tc qdisc add to the block bind function and,
in turn, to the setup_tc ndo of binding device via the tc_block_offload
struct. Pass this back to any block callback registrations to allow
netlink logging of fails in the bind process.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If RPADIR exists, the value written to it is always the same for all SoCs
(and derived from NET_IP_ALIGN), so there has not been any need to store
it in the *struct* sh_eth_cpu_data...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The *enum* RPADIR_BIT was declared in the commit 86a74ff21a7a ("net:
sh_eth: add support for Renesas SuperH Ethernet") adding SH771x support,
however the SH771x manual doesn't have the RPADIR register described and,
moreover, tells why the padding insertion must not be used. The newer SoC
manuals do have RPADIR documented, though with somewhat different layout --
update the *enum* according to these manuals...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far unsupported WoL options are silently ignored. Change this and
reject attempts to set unsupported options. This prevents situations
where a user tries to set an unsupported WoL option and is under the
impression it was successful because ethtool doesn't complain.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added the get_ts_info interface for ethtool to check
the timestamping capability.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add hardware timestamping support
for dpaa_eth. On Rx, timestamping is enabled for
all frames. On Tx, we only instruct the hardware
to timestamp the frames marked accordingly by the
stack.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Defined frame description command FM_FD_CMD_UPD for
prepended data updating.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add fman_port_get_tstamp() interface
to get timestamp.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add set_tstamp interface for memac,
dtsec, and 10GEC controllers to configure HW timestamping.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to support DPAA (Data Path Acceleration Architecture)
1588 timer by adding "fsl,fman-ptp-timer" compatible, sharing
interrupt with FMan, adding FSL_DPAA_ETH dependency, and fixing
up register offset.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to share fman event interrupt because
the 1588 timer driver will also use this interrupt.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When traffic passes through a router port, it needs to be assigned a FID
for ASIC to forward correctly. For bridges, this FID used to be the one
corresponding to VLAN 1. In a previous patch, this was changed to
instead use the PVID at the time that the RIF is created. This patch
guards PVID changes after the RIF was introduced.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to allow querying of the VID for which a RIF was created, add
a new function that returns a FID for a given RIF.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to guard against removal of a PVID for which a FID was
allocated, spectrum_switchdev needs to first determine whether there is
a RIF associated with a given bridge. To that end, publish a preexisting
function mlxsw_sp_rif_find_by_dev().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For bridge netdevices, instead of assuming that the router traffic is on
VLAN 1, look at the bridge PVID.
This patch assumes that the PVID doesn't change after the router
interface is created (i.e. after the IP address is assigned).
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the follow-up patch, mlxsw_sp_rif_vlan_fid_get() will be changed in a
way that could fail. Give that function a possibility to explain the
failure through extack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Manage pending per-NAPI GRO packets via list_head.
Return an SKB pointer from the GRO receive handlers. When GRO receive
handlers return non-NULL, it means that this SKB needs to be completed
at this time and removed from the NAPI queue.
Several operations are greatly simplified by this transformation,
especially timing out the oldest SKB in the list when gro_count
exceeds MAX_GRO_SKBS, and napi_gro_flush() which walks the queue
in reverse order.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Pull networking fixes from David Miller:
1) Fix netpoll OOPS in r8169, from Ville Syrjälä.
2) Fix bpf instruction alignment on powerpc et al., from Eric Dumazet.
3) Don't ignore IFLA_MTU attribute when creating new ipvlan links. From
Xin Long.
4) Fix use after free in AF_PACKET, from Eric Dumazet.
5) Mis-matched RTNL unlock in xen-netfront, from Ross Lagerwall.
6) Fix VSOCK loopback on big-endian, from Claudio Imbrenda.
7) Missing RX buffer offset correction when computing DMA addresses in
mvneta driver, from Antoine Tenart.
8) Fix crashes in DCCP's ccid3_hc_rx_send_feedback, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
sfc: make function efx_rps_hash_bucket static
strparser: Corrected typo in documentation.
qmi_wwan: add support for the Dell Wireless 5821e module
cxgb4: when disabling dcb set txq dcb priority to 0
net_sched: remove a bogus warning in hfsc
net: dccp: switch rx_tstamp_last_feedback to monotonic clock
net: dccp: avoid crash in ccid3_hc_rx_send_feedback()
net: Remove depends on HAS_DMA in case of platform dependency
MAINTAINERS: Add file patterns for dsa device tree bindings
net: mscc: make sparse happy
net: mvneta: fix the Rx desc DMA address in the Rx path
Documentation: e1000: Fix docs build error
Documentation: e100: Fix docs build error
Documentation: e1000: Use correct heading adornment
Documentation: e100: Use correct heading adornment
ipv6: mcast: fix unsolicited report interval after receiving querys
vhost_net: validate sock before trying to put its fd
VSOCK: fix loopback on big-endian systems
net: ethernet: ti: davinci_cpdma: make function cpdma_desc_pool_create static
xen-netfront: Update features after registering netdev
...
|
|
We can power down the PHY irregardless of WOL settings if interface
is down. So far we would have left the PHY enabled if WOL options
are set and the interface is brought down.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let's make saved_wolopts a shadow copy of the WoL options. This allows
to simplify the code and get rid of calls to now unneeded function
__rtl8169_get_wol(). However don't remove __rtl8169_get_wol()
completely to be prepared for the case that we can respect BIOS WOL
settings again.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let's move calling rtl8169_init_phy() to __rtl8169_resume().
It simplifies the code and avoids rtl8169_init_phy() being called
when resuming whilst interface is down. rtl_open() will initialize
the PHY when the interface is brought up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
-EOPNOTSUPP is the error value that should be reported if a flower
command is not supported by a driver. Fix it in couple of Intel drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the default case is not handled, which with future command
introductions would introduce a warning. So handle it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the default case is not handled, which with future command
introductions would introduce a warning. So handle it and make the
switch a bit simplier removing unneeded "rc" variable.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function efx_rps_hash_bucket is local to the source and
does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'efx_rps_hash_bucket' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Thomas Gleixner:
"Two fixlets for the EFI maze:
- Properly zero variables to prevent an early boot hang on EFI mixed
mode systems
- Fix the fallout of merging the 32bit and 64bit variants of EFI PCI
related code which ended up chosing the 32bit variant of the actual
EFi call invocation which leads to failures on 64bit"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Fix incorrect invocation of PciIo->Attributes()
efi/libstub/tpm: Initialize efi_physical_addr_t vars to zero for mixed mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for time(r) related issues:
- Fix a long standing conversion issue in jiffies_to_msecs() for odd
HZ values like 1024 or 1200 which resulted in returning 0 for small
jiffies values due to rounding down.
- Use the proper CONFIG symbol in the new Y2038 safe compat code for
posix-timers. Not yet a visible breakage, but this will immediately
trigger when the architecture support for the new interfaces is
merged.
- Return an error code in the STM32 clocksource driver on failure
instead of success.
- Remove the redundant and stale irq disabled check in the posix cpu
timer code. The check is at the wrong place anyway and lockdep
already covers it via the sighand lock locking coverage"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Make sure jiffies_to_msecs() preserves non-zero time periods
posix-timers: Fix nanosleep_copyout() for CONFIG_COMPAT_32BIT_TIME
clocksource/drivers/stm32: Fix error return code
posix-cpu-timers: Remove lockdep_assert_irqs_disabled()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes mostly for the ARM/GIC world:
- Fix the MSI affinity handling in the ls-scfg irq chip driver so it
updates and uses the effective affinity mask correctly
- Prevent binding LPIs to offline CPUs and respect the Cavium erratum
which requires that LPIs which belong to an offline NUMA node are
not bound to a CPU on a different NUMA node.
- Free only the amount of allocated interrupts in the GIC-V2M driver
instead of trying to free log2(nrirqs).
- Prevent emitting SYNC and VSYNC targetting non existing interrupt
collections in the GIC-V3 ITS driver
- Ensure that the GIV-V3 interrupt redistributor is correctly
reprogrammed on CPU hotplug
- Remove a stale unused helper function"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdesc: Delete irq_desc_get_msi_desc()
irqchip/gic-v3-its: Fix reprogramming of redistributors on CPU hotplug
irqchip/gic-v3-its: Only emit VSYNC if targetting a valid collection
irqchip/gic-v3-its: Only emit SYNC if targetting a valid collection
irqchip/gic-v3-its: Don't bind LPI to unavailable NUMA node
irqchip/gic-v2m: Fix SPI release on error path
irqchip/ls-scfg-msi: Fix MSI affinity handling
genirq/debugfs: Add missing IRQCHIP_SUPPORTS_LEVEL_MSI debug
|
|
When platform_device_register_simple() fails we can return
the error immediately instead of jumping to the 'err_pdev'
label.
This makes the error path a bit simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This module exposes two USB configurations: a QMI+AT capable setup on
USB config #1 and a MBIM capable setup on USB config #2.
By default the kernel will choose the MBIM capable configuration as
long as the cdc_mbim driver is available. This patch adds support for
the QMI port in the secondary configuration.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we are disabling DCB, store "0" in txq->dcb_prio
since that's used for future TX Work Request "OVLAN_IDX"
values. Setting non zero priority upon disabling DCB
would halt the traffic.
Reported-by: AMG Zollner Robert <robert@cloudmedia.eu>
CC: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull block fixes from Jens Axboe:
- Further timeout fixes. We aren't quite there yet, so expect another
round of fixes for that to completely close some of the IRQ vs
completion races. (Christoph/Bart)
- Set of NVMe fixes from the usual suspects, mostly error handling
- Two off-by-one fixes (Dan)
- Another bdi race fix (Jan)
- Fix nbd reconfigure with NBD_DISCONNECT_ON_CLOSE (Doron)
* tag 'for-linus-20180623' of git://git.kernel.dk/linux-block:
blk-mq: Fix timeout handling in case the timeout handler returns BLK_EH_DONE
bdi: Fix another oops in wb_workfn()
lightnvm: Remove depends on HAS_DMA in case of platform dependency
nvme-pci: limit max IO size and segments to avoid high order allocations
nvme-pci: move nvme_kill_queues to nvme_remove_dead_ctrl
nvme-fc: release io queues to allow fast fail
nbd: Add the nbd NBD_DISCONNECT_ON_CLOSE config flag.
block: sed-opal: Fix a couple off by one bugs
blk-mq-debugfs: Off by one in blk_mq_rq_state_name()
nvmet: reset keep alive timer in controller enable
nvme-rdma: don't override opts->queue_size
nvme-rdma: Fix command completion race at error recovery
nvme-rdma: fix possible free of a non-allocated async event buffer
nvme-rdma: fix possible double free condition when failing to create a controller
Revert "block: Add warning for bi_next not NULL in bio_endio()"
block: fix timeout changes for legacy request drivers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Fix use after free in chtls
- Fix RBP breakage in sha3
- Fix use after free in hwrng_unregister
- Fix overread in morus640
- Move sleep out of kernel_neon in arm64/aes-blk
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: core - Always drop the RNG in hwrng_unregister()
crypto: morus640 - Fix out-of-bounds access
crypto: don't optimize keccakf()
crypto: arm64/aes-blk - fix and move skcipher_walk_done out of kernel_neon_begin, _end
crypto: chtls - use after free in chtls_pt_recvmsg()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"This contains the following fixes/cleanups:
- the removal of a BUG_ON() which wasn't necessary and which could
trigger now due to a recent change
- a correction of a long standing bug happening very rarely in Xen
dom0 when a hypercall buffer from user land was not accessible by
the hypervisor for very short periods of time due to e.g. page
migration or compaction
- usage of EXPORT_SYMBOL_GPL() instead of EXPORT_SYMBOL() in a
Xen-related driver (no breakage possible as using those symbols
without others already exported via EXPORT-SYMBOL_GPL() wouldn't
make any sense)
- a simplification for Xen PVH or Xen ARM guests
- some additional error handling for callers of xenbus_printf()"
* tag 'for-linus-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Remove unnecessary BUG_ON from __unbind_from_irq()
xen: add new hypercall buffer mapping device
xen/scsiback: add error handling for xenbus_printf
scsi: xen-scsifront: add error handling for xenbus_printf
xen/grant-table: Export gnttab_{alloc|free}_pages as GPL
xen: add error handling for xenbus_printf
xen: share start flags between PV and PVH
|
|
Let's enable ASPM also on the RTL8168E-VL (chip version 34).
Works fine on my Zotac Mini PC with this chip. Temperature when
being idle is significantly lower than before due to reaching
deeper PC states.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The r8168 vendor driver always uses value 0x27. In r8169 we have few
chips where 0x17 is used. So far this didn't matter because ASPM was
disabled anyway. Now that ASPM was re-enabled let's also use 0x27 only.
One of the chips affected by this change is RTL8168E-VL, on my system
with this chip value 0x27 works fine.
In addition rename rtl_csi_access_enable_2() to
rtl_set_def_aspm_entry_latency() to make clear that we set the default
ASPM entry latency.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor pch_gbe_set_multi in order to avoid unnecessary indentation &
make it clearer what the code is doing.
The one behavioral change from this patch is that we'll no longer
configure the MAC address registers for multicast addresses when the
IFF_PROMISC or IFF_ALLMULTI flags are set. In these cases, just as when
we want to monitor more multicast addresses than we have MAC address
registers, we disable multicast filtering so the MAC address registers
are unused.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pch_gbe driver sets up multicast address filters using a convoluted
mechanism by which pch_gbe_set_multi allocates an array to hold
multicast addresses, copies desired addresses into that array, calls a
pch_gbe_mac_mc_addr_list_update function which copies addresses out of
that array into MAC registers, then frees the array.
This patch simplifies this somewhat by inlining
pch_gbe_mac_mc_addr_list_update into pch_gbe_set_multi, and removing the
requirement for the MAC addresses to stored consecutively in a single
array.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the module_pci_driver() macro to remove some needless
boilerplate code from the pch_gbe driver. This does have the side effect
of removing the print of the driver's version during probe, but this is
pretty useless information anyway - the version has changed only once
whilst the driver has been in mainline, despite many changes being made
to it before and since.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pch_gbe driver includes some code which appears to be an attempt to
work around a problem with the pch_gbe_free_rx_resources &
pch_gbe_free_tx_resources functions that no longer exists. Remove the
code guarded by the never-defined RINGFREE preprocessor macro.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pch_gbe driver currently presumes that the PHY is connected using
RGMII, and would need further work to support other buses. It includes a
define which is always set that conditionalises some of the
RGMII-specific code regardless. Remove it. If we do ever support
different MII buses then preprocessor defines won't be the best way to
select between them anyway.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pch_gbe driver calls a pch_gbe_hal_setup_init_funcs function which
ultimately sets the value of one field in struct pch_gbe_phy_info in a
convoluted way.
This patch removes pch_gbe_hal_setup_init_funcs in favor of inlining it,
and in turn its callee pch_gbe_plat_init_function_pointers, into the
single caller pch_gbe_sw_init.
With this pch_gbe_api.c & pch_gbe_api.h are essentially empty, so they
are removed & inclusions of the latter replaced with pch_gbe_phy.h which
was previously being included via pch_gbe_api.h.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For some reason the pch_gbe driver contains a struct pch_gbe_functions
with pointers used by a HAL abstraction layer, even though there is only
one implementation of each function.
This patch removes the get_bus_info abstraction. Its single
implementation (pch_gbe_plat_get_bus_info) only sets values within a
struct pch_gbe_bus_info which is never used, so we simply remove the
call to it in pch_gbe_probe & remove struct pch_gbe_bus_info entirely.
Now that struct pch_gbe_functions is empty we remove it entirely too.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For some reason the pch_gbe driver contains a struct pch_gbe_functions
with pointers used by a HAL abstraction layer, even though there is only
one implementation of each function.
This patch removes the init_hw abstraction in favor of inlining its
single implementation (pch_gbe_plat_init_hw) into its single caller
(pch_gbe_reset).
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For some reason the pch_gbe driver contains a struct pch_gbe_functions
with pointers used by a HAL abstraction layer, even though there is only
one implementation of each function.
This patch removes the read_phy_reg & write_phy_reg abstractions in
favor of calling pch_gbe_phy_read_reg_miic & pch_gbe_phy_write_reg_miic
directly.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For some reason the pch_gbe driver contains a struct pch_gbe_functions
with pointers used by a HAL abstraction layer, even though there is only
one implementation of each function.
This patch removes the reset_phy abstraction in favor of calling
pch_gbe_phy_hw_reset directly.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
