| Age | Commit message (Collapse) | Author |
|---|
|
Add support for netdev-genl, allowing users to query IRQ, NAPI, and queue
information.
After this patch is applied, note the IRQs assigned to my NIC:
$ cat /proc/interrupts | grep ens | cut -f1 --delimiter=':'
50
51
52
While e1000e allocates 3 IRQs (RX, TX, and other), it looks like e1000e
only has a single NAPI, so I've associated the NAPI with the RX IRQ (50
on my system, seen above).
Note the output from the cli:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 2}'
[{'id': 145, 'ifindex': 2, 'irq': 50}]
This device supports only 1 rx and 1 tx queue. so querying that:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump queue-get --json='{"ifindex": 2}'
[{'id': 0, 'ifindex': 2, 'napi-id': 145, 'type': 'rx'},
{'id': 0, 'ifindex': 2, 'napi-id': 145, 'type': 'tx'}]
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Duplicated register initialization codes exist in e1000_configure_tx()
and e1000_configure_rx().
For example, writel(0, tx_ring->head) writes 0 to tx_ring->head, which
is adapter->hw.hw_addr + E1000_TDH(0).
This initialization is already done in ew32(TDH(0), 0).
ew32(TDH(0), 0) is equivalent to __ew32(hw, E1000_TDH(0), 0). It
executes writel(0, hw->hw_addr + E1000_TDH(0)). Since variable hw is
set to &adapter->hw, it is equal to writel(0, tx_ring->head).
We can remove similar four writel() in e1000_configure_tx() and
e1000_configure_rx().
commit 0845d45e900c ("e1000e: Modify Tx/Rx configurations to avoid
null pointer dereferences in e1000_open") has introduced these
writel(). This commit moved register writing to
e1000_configure_tx/rx(), and as result, it caused duplication in
e1000_configure_tx/rx().
This patch modifies the sequence of register writing, but removing
these writes is safe because the same writes were already there before
the commit.
I also have checked the datasheets [0] [1] and have not found any
description that we need to write RDH, RDT, TDH and TDT registers
twice at initialization. Furthermore, we have tested this patch on an
I219-V device physically.
Link: https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/82577-gbe-phy-datasheet.pdf [0]
Link: https://www.intel.com/content/www/us/en/content-details/613460/intel-82583v-gbe-controller-datasheet.html [1]
Tested-by: Kohei Enju <enjuk@amazon.com>
Signed-off-by: Takamitsu Iwai <takamitz@amazon.co.jp>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
e1000_init_function_pointers_82575() is never implemented and used since
commit 9d5c824399de ("igb: PCI-Express 82575 Gigabit Ethernet driver").
And commit 9835fd7321a6 ("igb: Add new function to read part number from
EEPROM in string format") removed igb_read_part_num() implementation.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There is no caller and implementation in tree.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Since commit fff292b47ac1 ("ice: add VF representors one by one")
ice_eswitch_configure() is not used anymore.
Commit 1b8f15b64a00 ("ice: refactor filter functions") removed
ice_vsi_cfg_mac_fltr() but leave declaration.
Commit a24b4c6e9aab ("ice: xsk: Do not convert to buff to frame for
XDP_TX") leave ice_xmit_xdp_buff() declaration.
Commit 7cab44f1c35f ("ice: Introduce ETH56G PHY model for E825C
products") declared ice_phy_cfg_{rx,tx}_offset_eth56g(),
commit a1ffafb0b4a4 ("ice: Support configuring the device to Double
VLAN Mode") declared ice_pkg_buf_get_free_space(), and
commit 8a3a565ff210 ("ice: add admin commands to access cgu
configuration") declared ice_is_pca9575_present(), but all these never
be implemented.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Sporadic issues, such as PHY access loss, have been observed on I219 (19)
devices. It was found that these devices have hardware more closely
related to ADP than MTP and the issues were caused by taking MTP-specific
flows.
Change the MAC and board types of these devices from MTP to ADP to
correctly reflect the LAN hardware, and flows, of these devices.
Fixes: db2d737d63c5 ("e1000e: Separate MTP board type from ADP")
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 004d25060c78 ("igb: Fix igb_down hung on surprise removal")
changed igb_io_error_detected() to ignore non-fatal pcie errors in order
to avoid hung task that can happen when igb_down() is called multiple
times. This caused an issue when processing transient non-fatal errors.
igb_io_resume(), which is called after igb_io_error_detected(), assumes
that device is brought down by igb_io_error_detected() if the interface
is up. This resulted in panic with stacktrace below.
[ T3256] igb 0000:09:00.0 haeth0: igb: haeth0 NIC Link is Down
[ T292] pcieport 0000:00:1c.5: AER: Uncorrected (Non-Fatal) error received: 0000:09:00.0
[ T292] igb 0000:09:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID)
[ T292] igb 0000:09:00.0: device [8086:1537] error status/mask=00004000/00000000
[ T292] igb 0000:09:00.0: [14] CmpltTO [ 200.105524,009][ T292] igb 0000:09:00.0: AER: TLP Header: 00000000 00000000 00000000 00000000
[ T292] pcieport 0000:00:1c.5: AER: broadcast error_detected message
[ T292] igb 0000:09:00.0: Non-correctable non-fatal error reported.
[ T292] pcieport 0000:00:1c.5: AER: broadcast mmio_enabled message
[ T292] pcieport 0000:00:1c.5: AER: broadcast resume message
[ T292] ------------[ cut here ]------------
[ T292] kernel BUG at net/core/dev.c:6539!
[ T292] invalid opcode: 0000 [#1] PREEMPT SMP
[ T292] RIP: 0010:napi_enable+0x37/0x40
[ T292] Call Trace:
[ T292] <TASK>
[ T292] ? die+0x33/0x90
[ T292] ? do_trap+0xdc/0x110
[ T292] ? napi_enable+0x37/0x40
[ T292] ? do_error_trap+0x70/0xb0
[ T292] ? napi_enable+0x37/0x40
[ T292] ? napi_enable+0x37/0x40
[ T292] ? exc_invalid_op+0x4e/0x70
[ T292] ? napi_enable+0x37/0x40
[ T292] ? asm_exc_invalid_op+0x16/0x20
[ T292] ? napi_enable+0x37/0x40
[ T292] igb_up+0x41/0x150
[ T292] igb_io_resume+0x25/0x70
[ T292] report_resume+0x54/0x70
[ T292] ? report_frozen_detected+0x20/0x20
[ T292] pci_walk_bus+0x6c/0x90
[ T292] ? aer_print_port_info+0xa0/0xa0
[ T292] pcie_do_recovery+0x22f/0x380
[ T292] aer_process_err_devices+0x110/0x160
[ T292] aer_isr+0x1c1/0x1e0
[ T292] ? disable_irq_nosync+0x10/0x10
[ T292] irq_thread_fn+0x1a/0x60
[ T292] irq_thread+0xe3/0x1a0
[ T292] ? irq_set_affinity_notifier+0x120/0x120
[ T292] ? irq_affinity_notify+0x100/0x100
[ T292] kthread+0xe2/0x110
[ T292] ? kthread_complete_and_exit+0x20/0x20
[ T292] ret_from_fork+0x2d/0x50
[ T292] ? kthread_complete_and_exit+0x20/0x20
[ T292] ret_from_fork_asm+0x11/0x20
[ T292] </TASK>
To fix this issue igb_io_resume() checks if the interface is running and
the device is not down this means igb_io_error_detected() did not bring
the device down and there is no need to bring it up.
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Reviewed-by: Yuanyuan Zhong <yzhong@purestorage.com>
Fixes: 004d25060c78 ("igb: Fix igb_down hung on surprise removal")
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This patch addresses a macvlan leak issue in the i40e driver caused by
concurrent access to vsi->mac_filter_hash. The leak occurs when multiple
threads attempt to modify the mac_filter_hash simultaneously, leading to
inconsistent state and potential memory leaks.
To fix this, we now wrap the calls to i40e_del_mac_filter() and zeroing
vf->default_lan_addr.addr with spin_lock/unlock_bh(&vsi->mac_filter_hash_lock),
ensuring atomic operations and preventing concurrent access.
Additionally, we add lockdep_assert_held(&vsi->mac_filter_hash_lock) in
i40e_add_mac_filter() to help catch similar issues in the future.
Reproduction steps:
1. Spawn VFs and configure port vlan on them.
2. Trigger concurrent macvlan operations (e.g., adding and deleting
portvlan and/or mac filters).
3. Observe the potential memory leak and inconsistent state in the
mac_filter_hash.
This synchronization ensures the integrity of the mac_filter_hash and prevents
the described leak.
Fixes: fed0d9f13266 ("i40e: Fix VF's MAC Address change on VM")
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add jump targets so that a bit of exception handling can be better reused
at the end of two function implementations.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We have for some time the assign_bit() API to replace open coded
if (foo)
set_bit(n, bar);
else
clear_bit(n, bar);
Use this API to clean the code. No functional change intended.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The max_frame and rx_buf_len fields of the VSI set the maximum frame size
for packets on the wire, and configure the size of the Rx buffer. In the
hardware, these are per-queue configuration. Most VSI types use a simple
method to determine the size of the buffers for all queues.
However, VFs may potentially configure different values for each queue.
While the Linux iAVF driver does not do this, it is allowed by the virtchnl
interface.
The current virtchnl code simply sets the per-VSI fields inbetween calls to
ice_vsi_cfg_single_rxq(). This technically works, as these fields are only
ever used when programming the Rx ring, and otherwise not checked again.
However, it is confusing to maintain.
The Rx ring also already has an rx_buf_len field in order to access the
buffer length in the hotpath. It also has extra unused bytes in the ring
structure which we can make use of to store the maximum frame size.
Drop the VSI max_frame and rx_buf_len fields. Add max_frame to the Rx ring,
and slightly re-order rx_buf_len to better fit into the gaps in the
structure layout.
Change the ice_vsi_cfg_frame_size function so that it writes to the ring
fields. Call this function once per ring in ice_vsi_cfg_rxqs(). This is
done over calling it inside the ice_vsi_cfg_rxq(), because
ice_vsi_cfg_rxq() is called in the virtchnl flow where the max_frame and
rx_buf_len have already been configured.
Change the accesses for rx_buf_len and max_frame to all point to the ring
structure. This has the added benefit that ice_vsi_cfg_rxq() no longer has
the surprise side effect of updating ring->rx_buf_len based on the VSI
field.
Update the virtchnl ice_vc_cfg_qs_msg() function to set the ring values
directly, and drop references to the removed VSI fields.
This now makes the VF logic clear, as the ring fields are obviously
per-queue. This reduces the required cognitive load when reasoning about
this logic.
Note that removing the VSI fields does leave a 4 byte gap, but the ice_vsi
structure has many gaps, and its layout is not as critical in the hot path.
The structure may benefit from a more thorough repacking, but no attempt
was made in this change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_vc_cfg_qs_msg() function is used to configure VF queues in response
to a VIRTCHNL_OP_CONFIG_VSI_QUEUES command.
The virtchnl command contains an array of queue pair data for configuring
Tx and Rx queues. This data includes a queue ID. When configuring the
queues, the driver generally uses this queue ID to determine which Tx and
Rx ring to program. However, a handful of places use the index into the
queue pair data from the VF. While most VF implementations appear to send
this data in order, it is not mandated by the virtchnl and it is not
verified that the queue pair data comes in order.
Fix the driver to consistently use the q_idx field instead of the 'i'
iterator value when accessing the rings. For the Rx case, introduce a local
ring variable to keep lines short.
Fixes: 7ad15440acf8 ("ice: Refactor VIRTCHNL_OP_CONFIG_VSI_QUEUES handling")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
E830 adds hardware support to prevent the VF from overflowing the PF
mailbox with VIRTCHNL messages. E830 will use the hardware feature
(ICE_F_MBX_LIMIT) instead of the software solution ice_is_malicious_vf().
To prevent a VF from overflowing the PF, the PF sets the number of
messages per VF that can be in the PF's mailbox queue
(ICE_MBX_OVERFLOW_WATERMARK). When the PF processes a message from a VF,
the PF decrements the per VF message count using the E830_MBX_VF_DEC_TRIG
register.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Enable ethtool reset support. Ethtool reset flags are mapped to the
E810 reset type:
PF reset:
$ ethtool --reset <ethX> irq dma filter offload
CORE reset:
$ ethtool --reset <ethX> irq-shared dma-shared filter-shared \
offload-shared ram-shared
GLOBAL reset:
$ ethtool --reset <ethX> irq-shared dma-shared filter-shared \
offload-shared mac-shared phy-shared ram-shared
Calling the same set of flags as in PF reset case on port representor
triggers VF reset.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Increasing MSI-X value on a VF leads to invalid memory operations. This
is caused by not reallocating some arrays.
Reproducer:
modprobe ice
echo 0 > /sys/bus/pci/devices/$PF_PCI/sriov_drivers_autoprobe
echo 1 > /sys/bus/pci/devices/$PF_PCI/sriov_numvfs
echo 17 > /sys/bus/pci/devices/$VF0_PCI/sriov_vf_msix_count
Default MSI-X is 16, so 17 and above triggers this issue.
KASAN reports:
BUG: KASAN: slab-out-of-bounds in ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
Read of size 8 at addr ffff8888b937d180 by task bash/28433
(...)
Call Trace:
(...)
? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
kasan_report+0xed/0x120
? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
ice_vsi_cfg_def+0x3360/0x4770 [ice]
? mutex_unlock+0x83/0xd0
? __pfx_ice_vsi_cfg_def+0x10/0x10 [ice]
? __pfx_ice_remove_vsi_lkup_fltr+0x10/0x10 [ice]
ice_vsi_cfg+0x7f/0x3b0 [ice]
ice_vf_reconfig_vsi+0x114/0x210 [ice]
ice_sriov_set_msix_vec_count+0x3d0/0x960 [ice]
sriov_vf_msix_count_store+0x21c/0x300
(...)
Allocated by task 28201:
(...)
ice_vsi_cfg_def+0x1c8e/0x4770 [ice]
ice_vsi_cfg+0x7f/0x3b0 [ice]
ice_vsi_setup+0x179/0xa30 [ice]
ice_sriov_configure+0xcaa/0x1520 [ice]
sriov_numvfs_store+0x212/0x390
(...)
To fix it, use ice_vsi_rebuild() instead of ice_vf_reconfig_vsi(). This
causes the required arrays to be reallocated taking the new queue count
into account (ice_vsi_realloc_stat_arrays()). Set req_txq and req_rxq
before ice_vsi_rebuild(), so that realloc uses the newly set queue
count.
Additionally, ice_vsi_rebuild() does not remove VSI filters
(ice_fltr_remove_all()), so ice_vf_init_host_cfg() is no longer
necessary.
Reported-by: Jacob Keller <jacob.e.keller@intel.com>
Fixes: 2a2cb4c6c181 ("ice: replace ice_vf_recreate_vsi() with ice_vf_reconfig_vsi()")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Triggering the reset while in switchdev mode causes
errors[1]. Rules are already removed by this time
because switch content is flushed in case of the reset.
This means that rules were deleted from HW but SW
still thinks they exist so when we get
SWITCHDEV_FDB_DEL_TO_DEVICE notification we try to
delete not existing rule.
We can avoid these errors by clearing the rules
early in the reset flow before they are removed from HW.
Switchdev API will get notified that the rule was removed
so we won't get SWITCHDEV_FDB_DEL_TO_DEVICE notification.
Remove unnecessary ice_clear_sw_switch_recipes.
[1]
ice 0000:01:00.0: Failed to delete FDB forward rule, err: -2
ice 0000:01:00.0: Failed to delete FDB guard rule, err: -2
Fixes: 7c945a1a8e5f ("ice: Switchdev FDB events support")
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
netif_is_ice() works by checking the pointer to netdev ops. However, it
only checks for the default ice_netdev_ops, not ice_netdev_safe_mode_ops,
so in Safe Mode it always returns false, which is unintuitive. While it
doesn't look like netif_is_ice() is currently being called anywhere in Safe
Mode, this could change and potentially lead to unexpected behaviour.
Fixes: df006dd4b1dc ("ice: Add initial support framework for LAG")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
If DDP package is missing or corrupted, the driver should enter Safe Mode.
Instead, an error is returned and probe fails.
To fix this, don't exit init if ice_init_ddp_config() returns an error.
Repro:
* Remove or rename DDP package (/lib/firmware/intel/ice/ddp/ice.pkg)
* Load ice
Fixes: cc5776fe1832 ("ice: Enable switching default Tx scheduler topology")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The sizeof(struct napi_struct) can change. Don't hardcode the size to
400 bytes and instead use "sizeof(struct napi_struct)".
Suggested-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/20241004105407.73585-1-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-10-01 (ice)
This series contains updates to ice driver only.
Karol cleans up current PTP GPIO pin handling, fixes minor bugs,
refactors implementation for all products, introduces SDP (Software
Definable Pins) for E825C and implements reading SDP section from NVM
for E810 products.
Sergey replaces multiple aux buses and devices used in the PTP support
code with struct ice_adapter holding the necessary shared data.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: Drop auxbus use for PTP to finalize ice_adapter move
ice: Use ice_adapter for PTP shared data instead of auxdev
ice: Initial support for E825C hardware in ice_adapter
ice: Add ice_get_ctrl_ptp() wrapper to simplify the code
ice: Introduce ice_get_phy_model() wrapper
ice: Enable 1PPS out from CGU for E825C products
ice: Read SDP section from NVM for pin definitions
ice: Disable shared pin on E810 on setfunc
ice: Cache perout/extts requests and check flags
ice: Align E810T GPIO to other products
ice: Add SDPs support for E825C
ice: Implement ice_ptp_pin_desc
====================
Link: https://patch.msgid.link/20241001201702.3252954-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-09-30 (ice, idpf)
This series contains updates to ice and idpf drivers:
For ice:
Michal corrects setting of dst VSI on LAN filters and adds clearing of
port VLAN configuration during reset.
Gui-Dong Han corrects failures to decrement refcount in some error
paths.
Przemek resolves a memory leak in ice_init_tx_topology().
Arkadiusz prevents setting of DPLL_PIN_STATE_SELECTABLE to an improper
value.
Dave stops clearing of VLAN tracking bit to allow for VLANs to be properly
restored after reset.
For idpf:
Ahmed sets uninitialized dyn_ctl_intrvl_s value.
Josh corrects use and reporting of mailbox size.
Larysa corrects order of function calls during de-initialization.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
idpf: deinit virtchnl transaction manager after vport and vectors
idpf: use actual mbx receive payload length
idpf: fix VF dynamic interrupt ctl register initialization
ice: fix VLAN replay after reset
ice: disallow DPLL_PIN_STATE_SELECTABLE for dpll output pins
ice: fix memleak in ice_init_tx_topology()
ice: clear port vlan config during reset
ice: Fix improper handling of refcount in ice_sriov_set_msix_vec_count()
ice: Fix improper handling of refcount in ice_dpll_init_rclk_pins()
ice: set correct dst VSI in only LAN filters
====================
Link: https://patch.msgid.link/20240930223601.3137464-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
Drop unused auxbus/auxdev support from the PTP code due to
move to the ice_adapter.
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use struct ice_adapter to hold shared PTP data and control PTP
related actions instead of auxbus. This allows significant code
simplification and faster access to the container fields used in
the PTP support code.
Move the PTP port list to the ice_adapter container to simplify
the code and avoid race conditions which could occur due to the
synchronous nature of the initialization/access and
certain memory saving can be achieved by moving PTP data into
the ice_adapter itself.
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Address E825C devices by PCI ID since dual IP core configurations
need 1 ice_adapter for both devices.
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add ice_get_ctrl_ptp() wrapper to simplify the PTP support code
in the functions that do not use ctrl_pf directly.
Add the control PF pointer to struct ice_adapter
Rearrange fields in struct ice_adapter
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Introduce ice_get_phy_model() to improve code readability
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Implement configuring 1PPS signal output from CGU. Use maximal amplitude
because Linux PTP pin API does not have any way for user to set signal
level.
This change is necessary for E825C products to properly output any
signal from 1PPS pin.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
PTP pins assignment and their related SDPs (Software Definable Pins) are
currently hardcoded.
Fix that by reading NVM section instead on products supporting this,
which are E810 products.
If SDP section is not defined in NVM, the driver continues to use the
hardcoded table.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Yochai Hagvi <yochai.hagvi@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When setting a new supported function for a pin on E810, disable other
enabled pin that shares the same GPIO.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Cache original PTP GPIO requests instead of saving each parameter in
internal structures for periodic output or external timestamp request.
Factor out all periodic output register writes from ice_ptp_cfg_clkout
to a separate function to improve readability.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Instead of having separate PTP GPIO implementation for E810T, use
existing one from all other products.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add support of PTP SDPs (Software Definable Pins) for E825C products.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add a new internal structure describing PTP pins.
Use the new structure for all non-E810T products.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When the device is removed, idpf is supposed to make certain virtchnl
requests e.g. VIRTCHNL2_OP_DEALLOC_VECTORS and VIRTCHNL2_OP_DESTROY_VPORT.
However, this does not happen due to the referenced commit introducing
virtchnl transaction manager and placing its deinitialization before those
messages are sent. Then the sending is impossible due to no transactions
being available.
Lack of cleanup can lead to the FW becoming unresponsive from e.g.
unloading-loading the driver and creating-destroying VFs afterwards.
Move transaction manager deinitialization to after other virtchnl-related
cleanup is done.
Fixes: 34c21fa894a1 ("idpf: implement virtchnl transaction manager")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When a mailbox message is received, the driver is checking for a non 0
datalen in the controlq descriptor. If it is valid, the payload is
attached to the ctlq message to give to the upper layer. However, the
payload response size given to the upper layer was taken from the buffer
metadata which is _always_ the max buffer size. This meant the API was
returning 4K as the payload size for all messages. This went unnoticed
since the virtchnl exchange response logic was checking for a response
size less than 0 (error), not less than exact size, or not greater than
or equal to the max mailbox buffer size (4K). All of these checks will
pass in the success case since the size provided is always 4K. However,
this breaks anyone that wants to validate the exact response size.
Fetch the actual payload length from the value provided in the
descriptor data_len field (instead of the buffer metadata).
Unfortunately, this means we lose some extra error parsing for variable
sized virtchnl responses such as create vport and get ptypes. However,
the original checks weren't really helping anyways since the size was
_always_ 4K.
Fixes: 34c21fa894a1 ("idpf: implement virtchnl transaction manager")
Cc: stable@vger.kernel.org # 6.9+
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The VF's dynamic interrupt ctl "dyn_ctl_intrvl_s" is not initialized
in idpf_vf_intr_reg_init(). This resulted in the following UBSAN error
whenever a VF is created:
[ 564.345655] UBSAN: shift-out-of-bounds in drivers/net/ethernet/intel/idpf/idpf_txrx.c:3654:10
[ 564.345663] shift exponent 4294967295 is too large for 32-bit type 'int'
[ 564.345671] CPU: 33 UID: 0 PID: 2458 Comm: NetworkManager Not tainted 6.11.0-rc4+ #1
[ 564.345678] Hardware name: Intel Corporation M50CYP2SBSTD/M50CYP2SBSTD, BIOS SE5C6200.86B.0027.P10.2201070222 01/07/2022
[ 564.345683] Call Trace:
[ 564.345688] <TASK>
[ 564.345693] dump_stack_lvl+0x91/0xb0
[ 564.345708] __ubsan_handle_shift_out_of_bounds+0x16b/0x320
[ 564.345730] idpf_vport_intr_update_itr_ena_irq.cold+0x13/0x39 [idpf]
[ 564.345755] ? __pfx_idpf_vport_intr_update_itr_ena_irq+0x10/0x10 [idpf]
[ 564.345771] ? static_obj+0x95/0xd0
[ 564.345782] ? lockdep_init_map_type+0x1a5/0x800
[ 564.345794] idpf_vport_intr_ena+0x5ef/0x9f0 [idpf]
[ 564.345814] idpf_vport_open+0x2cc/0x1240 [idpf]
[ 564.345837] idpf_open+0x6d/0xc0 [idpf]
[ 564.345850] __dev_open+0x241/0x420
Fixes: d4d558718266 ("idpf: initialize interrupts and enable vport")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There is a bug currently when there are more than one VLAN defined
and any reset that affects the PF is initiated, after the reset rebuild
no traffic will pass on any VLAN but the last one created.
This is caused by the iteration though the VLANs during replay each
clearing the vsi_map bitmap of the VSI that is being replayed. The
problem is that during rhe replay, the pointer to the vsi_map bitmap
is used by each successive vlan to determine if it should be replayed
on this VSI.
The logic was that the replay of the VLAN would replace the bit in the map
before the next VLAN would iterate through. But, since the replay copies
the old bitmap pointer to filt_replay_rules and creates a new one for the
recreated VLANS, it does not do this, and leaves the old bitmap broken
to be used to replay the remaining VLANs.
Since the old bitmap will be cleaned up in post replay cleanup, there is
no need to alter it and break following VLAN replay, so don't clear the
bit.
Fixes: 334cb0626de1 ("ice: Implement VSI replay framework")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently the user may request DPLL_PIN_STATE_SELECTABLE for an output
pin, and this would actually set the DISCONNECTED state instead.
It doesn't make any sense. SELECTABLE is valid only in case of input pins
(on AUTOMATIC type dpll), where dpll itself would select best valid input.
For the output pin only CONNECTED/DISCONNECTED are expected.
Fixes: d7999f5ea64b ("ice: implement dpll interface to control cgu")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix leak of the FW blob (DDP pkg).
Make ice_cfg_tx_topo() const-correct, so ice_init_tx_topology() can avoid
copying whole FW blob. Copy just the topology section, and only when
needed. Reuse the buffer allocated for the read of the current topology.
This was found by kmemleak, with the following trace for each PF:
[<ffffffff8761044d>] kmemdup_noprof+0x1d/0x50
[<ffffffffc0a0a480>] ice_init_ddp_config+0x100/0x220 [ice]
[<ffffffffc0a0da7f>] ice_init_dev+0x6f/0x200 [ice]
[<ffffffffc0a0dc49>] ice_init+0x29/0x560 [ice]
[<ffffffffc0a10c1d>] ice_probe+0x21d/0x310 [ice]
Constify ice_cfg_tx_topo() @buf parameter.
This cascades further down to few more functions.
Fixes: cc5776fe1832 ("ice: Enable switching default Tx scheduler topology")
CC: Larysa Zaremba <larysa.zaremba@intel.com>
CC: Jacob Keller <jacob.e.keller@intel.com>
CC: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
CC: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Since commit 2a2cb4c6c181 ("ice: replace ice_vf_recreate_vsi() with
ice_vf_reconfig_vsi()") VF VSI is only reconfigured instead of
recreated. The context configuration from previous setting is still the
same. If any of the config needs to be cleared it needs to be cleared
explicitly.
Previously there was assumption that port vlan will be cleared
automatically. Now, when VSI is only reconfigured we have to do it in the
code.
Not clearing port vlan configuration leads to situation when the driver
VSI config is different than the VSI config in HW. Traffic can't be
passed after setting and clearing port vlan, because of invalid VSI
config in HW.
Example reproduction:
> ip a a dev $(VF) $(VF_IP_ADDRESS)
> ip l s dev $(VF) up
> ping $(VF_IP_ADDRESS)
ping is working fine here
> ip link set eth5 vf 0 vlan 100
> ip link set eth5 vf 0 vlan 0
> ping $(VF_IP_ADDRESS)
ping isn't working
Fixes: 2a2cb4c6c181 ("ice: replace ice_vf_recreate_vsi() with ice_vf_reconfig_vsi()")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Piotr Tyda <piotr.tyda@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This patch addresses an issue with improper reference count handling in the
ice_sriov_set_msix_vec_count() function.
First, the function calls ice_get_vf_by_id(), which increments the
reference count of the vf pointer. If the subsequent call to
ice_get_vf_vsi() fails, the function currently returns an error without
decrementing the reference count of the vf pointer, leading to a reference
count leak. The correct behavior, as implemented in this patch, is to
decrement the reference count using ice_put_vf(vf) before returning an
error when vsi is NULL.
Second, the function calls ice_sriov_get_irqs(), which sets
vf->first_vector_idx. If this call returns a negative value, indicating an
error, the function returns an error without decrementing the reference
count of the vf pointer, resulting in another reference count leak. The
patch addresses this by adding a call to ice_put_vf(vf) before returning
an error when vf->first_vector_idx < 0.
This bug was identified by an experimental static analysis tool developed
by our team. The tool specializes in analyzing reference count operations
and identifying potential mismanagement of reference counts. In this case,
the tool flagged the missing decrement operation as a potential issue,
leading to this patch.
Fixes: 4035c72dc1ba ("ice: reconfig host after changing MSI-X on VF")
Fixes: 4d38cb44bd32 ("ice: manage VFs MSI-X using resource tracking")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <hanguidong02@outlook.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This patch addresses a reference count handling issue in the
ice_dpll_init_rclk_pins() function. The function calls ice_dpll_get_pins(),
which increments the reference count of the relevant resources. However,
if the condition WARN_ON((!vsi || !vsi->netdev)) is met, the function
currently returns an error without properly releasing the resources
acquired by ice_dpll_get_pins(), leading to a reference count leak.
To resolve this, the check has been moved to the top of the function. This
ensures that the function verifies the state before any resources are
acquired, avoiding the need for additional resource management in the
error path.
This bug was identified by an experimental static analysis tool developed
by our team. The tool specializes in analyzing reference count operations
and detecting potential issues where resources are not properly managed.
In this case, the tool flagged the missing release operation as a
potential problem, which led to the development of this patch.
Fixes: d7999f5ea64b ("ice: implement dpll interface to control cgu")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <hanguidong02@outlook.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The filters set that will reproduce the problem:
$ tc filter add dev $VF0_PR ingress protocol arp prio 0 flower \
skip_sw dst_mac ff:ff:ff:ff:ff:ff action mirred egress \
redirect dev $PF0
$ tc filter add dev $VF0_PR ingress protocol arp prio 0 flower \
skip_sw dst_mac ff:ff:ff:ff:ff:ff src_mac 52:54:00:00:00:10 \
action mirred egress mirror dev $VF1_PR
Expected behaviour is to set all broadcast from VF0 to the LAN. If the
src_mac match the value from filters, send packet to LAN and to VF1.
In this case both LAN_EN and LB_EN flags in switch is set in case of
packet matching both filters. As dst VSI for the only LAN enable bit is
PF VSI, the packet is being seen on PF. To fix this change dst VSI to
the source VSI. It will block receiving any packet even when LB_EN is
set by switch, because local loopback is clear on VF VSI during normal
operation.
Side note: if the second filters action is redirect instead of mirror
LAN_EN is clear, because switch is AND-ing LAN_EN from each matched
filters and OR-ing LB_EN.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Fixes: 73b483b79029 ("ice: Manage act flags for switchdev offloads")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_allocate_sf() function returns error pointers on error. It
doesn't return NULL. Update the check to match.
Fixes: 177ef7f1e2a0 ("ice: base subfunction aux driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/6951d217-ac06-4482-a35d-15d757fd90a3@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ice_repr_create() function returns error pointers. It never returns
NULL. Fix the callers to check for IS_ERR().
Fixes: 977514fb0fa8 ("ice: create port representor for SF")
Fixes: 415db8399d06 ("ice: make representor code generic")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/7f7aeb91-8771-47b8-9275-9d9f64f947dd@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts (sort of) and no adjacent changes.
This merge reverts commit b3c9e65eb227 ("net: hsr: remove seqnr_lock")
from net, as it was superseded by
commit 430d67bdcb04 ("net: hsr: Use the seqnr lock for frames received via interlink port.")
in net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
idpf: XDP chapter II: convert Tx completion to libeth
Alexander Lobakin says:
XDP for idpf is currently 5 chapters:
* convert Rx to libeth;
* convert Tx completion to libeth (this);
* generic XDP and XSk code changes;
* actual XDP for idpf via libeth_xdp;
* XSk for idpf (^).
Part II does the following:
* adds generic libeth Tx completion routines;
* converts idpf to use generic libeth Tx comp routines;
* fixes Tx queue timeouts and robustifies Tx completion in general;
* fixes Tx event/descriptor flushes (writebacks).
Most idpf patches again remove more lines than adds.
Generic Tx completion helpers and structs are needed as libeth_xdp
(Ch. III) makes use of them. WB_ON_ITR is needed since XDPSQs don't
want to work without it at all. Tx queue timeouts fixes are needed
since without them, it's way easier to catch a Tx timeout event when
WB_ON_ITR is enabled.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
idpf: enable WB_ON_ITR
idpf: fix netdev Tx queue stop/wake
idpf: refactor Tx completion routines
netdevice: add netdev_tx_reset_subqueue() shorthand
idpf: convert to libeth Tx buffer completion
libeth: add Tx buffer completion helpers
====================
Link: https://patch.msgid.link/20240909205323.3110312-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tell hardware to write back completed descriptors even when interrupts
are disabled. Otherwise, descriptors might not be written back until
the hardware can flush a full cacheline of descriptors. This can cause
unnecessary delays when traffic is light (or even trigger Tx queue
timeout).
The example scenario to reproduce the Tx timeout if the fix is not
applied:
- configure at least 2 Tx queues to be assigned to the same q_vector,
- generate a huge Tx traffic on the first Tx queue
- try to send a few packets using the second Tx queue.
In such a case Tx timeout will appear on the second Tx queue because no
completion descriptors are written back for that queue while interrupts
are disabled due to NAPI polling.
Fixes: c2d548cad150 ("idpf: add TX splitq napi poll support")
Fixes: a5ab9ee0df0b ("idpf: add singleq start_xmit and napi poll")
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Co-developed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
netif_txq_maybe_stop() returns -1, 0, or 1, while
idpf_tx_maybe_stop_common() says it returns 0 or -EBUSY. As a result,
there sometimes are Tx queue timeout warnings despite that the queue
is empty or there is at least enough space to restart it.
Make idpf_tx_maybe_stop_common() inline and returning true or false,
handling the return of netif_txq_maybe_stop() properly. Use a correct
goto in idpf_tx_maybe_stop_splitq() to avoid stopping the queue or
incrementing the stops counter twice.
Fixes: 6818c4d5b3c2 ("idpf: add splitq start_xmit")
Fixes: a5ab9ee0df0b ("idpf: add singleq start_xmit and napi poll")
Cc: stable@vger.kernel.org # 6.7+
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
