| Age | Commit message (Collapse) | Author |
|---|
|
The ice_nvm_write_activate function is used to issue AdminQ command
0x0707 which sends a request to firmware to activate a flash bank. For
basic operations, this command takes an 8bit flag value which defines
the flags to control the activation process. There are some additional
flags that are stored in a second 8bit flag field.
We can simplify the interface by using a u16 cmd_flags variable. Split
this over the two bytes of flag storage in the structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice hardware contains an embedded chip with firmware which can be
updated using devlink flash. The firmware which runs on this chip is
referred to as the Embedded Management Processor firmware (EMP
firmware).
Activating the new firmware image currently requires that the system be
rebooted. This is not ideal as rebooting the system can cause unwanted
downtime.
In practical terms, activating the firmware does not always require a
full system reboot. In many cases it is possible to activate the EMP
firmware immediately. There are a couple of different scenarios to
cover.
* The EMP firmware itself can be reloaded by issuing a special update
to the device called an Embedded Management Processor reset (EMP
reset). This reset causes the device to reset and reload the EMP
firmware.
* PCI configuration changes are only reloaded after a cold PCIe reset.
Unfortunately there is no generic way to trigger this for a PCIe
device without a system reboot.
When performing a flash update, firmware is capable of responding with
some information about the specific update requirements.
The driver updates the flash by programming a secondary inactive bank
with the contents of the new image, and then issuing a command to
request to switch the active bank starting from the next load.
The response to the final command for updating the inactive NVM flash
bank includes an indication of the minimum reset required to fully
update the device. This can be one of the following:
* A full power on is required
* A cold PCIe reset is required
* An EMP reset is required
The response to the command to switch flash banks includes an indication
of whether or not the firmware will allow an EMP reset request.
For most updates, an EMP reset is sufficient to load the new EMP
firmware without issues. In some cases, this reset is not sufficient
because the PCI configuration space has changed. When this could cause
incompatibility with the new EMP image, the firmware is capable of
rejecting the EMP reset request.
Add logic to ice_fw_update.c to handle the response data flash update
AdminQ commands.
For the reset level, issue a devlink status notification informing the
user of how to complete the update with a simple suggestion like
"Activate new firmware by rebooting the system".
Cache the status of whether or not firmware will restrict the EMP reset
for use in implementing devlink reload.
Implement support for devlink reload with the "fw_activate" flag. This
allows user space to request the firmware be activated immediately.
For the .reload_down handler, we will issue a request for the EMP reset
using the appropriate firmware AdminQ command. If we know that the
firmware will not allow an EMP reset, simply exit with a suitable
netlink extended ACK message indicating that the EMP reset is not
available.
For the .reload_up handler, simply wait until the driver has finished
resetting. Logic to handle processing of an EMP reset already exists in
the driver as part of its reset and rebuild flows.
Implement support for the devlink reload interface with the
"fw_activate" action. This allows userspace to request activation of
firmware without a reboot.
Note that support for indicating the required reset and EMP reset
restriction is not supported on old versions of firmware. The driver can
determine if the two features are supported by checking the device
capabilities report. I confirmed support has existed since at least
version 5.5.2 as reported by the 'fw.mgmt' version. Support to issue the
EMP reset request has existed in all version of the EMP firmware for the
ice hardware.
Check the device capabilities report to determine whether or not the
indications are reported by the running firmware. If the reset
requirement indication is not supported, always assume a full power on
is necessary. If the reset restriction capability is not supported,
always assume the EMP reset is available.
Users can verify if the EMP reset has activated the firmware by using
the devlink info report to check that the 'running' firmware version has
updated. For example a user might do the following:
# Check current version
$ devlink dev info
# Update the device
$ devlink dev flash pci/0000:af:00.0 file firmware.bin
# Confirm stored version updated
$ devlink dev info
# Reload to activate new firmware
$ devlink dev reload pci/0000:af:00.0 action fw_activate
# Confirm running version updated
$ devlink dev info
Finally, this change does *not* implement basic driver-only reload
support. I did look into trying to do this. However, it requires
significant refactor of how the ice driver probes and loads everything.
The ice driver probe and allocation flows were not designed with such
a reload in mind. Refactoring the flow to support this is beyond the
scope of this change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Clean up code after changing ice_status to int. Rearrange to fix reverse
Christmas tree and pull lines up where applicable.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
To prepare for removal of ice_status, change the variables from
ice_status to int. This eases the transition when values are changed to
return standard int error codes over enum ice_status.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
Just as we recently added support for other stored firmware flash
versions, support display of the stored UNDI Option ROM version via
devlink info.
To do this, we need to introduce a new ice_get_inactive_orom_ver
function. This is a little trickier than with other flash versions. The
Option ROM version data was being read from a special "Boot
Configuration" block of the NVM Preserved Field Area. This block only
contains the *active* Option ROM version data. It is populated when the
device firmware finishes updating the Option ROM.
This method is ineffective at reading the stored Option ROM version
data. Instead of reading from this section of the flash, replace this
version extraction with one which locates the Combo Version information
from within the Option ROM binary.
This data is stored within the Option ROM at a 512 byte offset, in
a simple structured format. The structure uses a simple modulo 256
checksum for integrity verification. Scan through the Option ROM to
locate the CIVD data section, and extract the Combo Version.
Refactor ice_get_orom_ver_info so that it takes the bank select
enumeration parameter. Use this to implement ice_get_inactive_orom_ver.
Although all ice devices have a Boot Configuration block in the NVM PFA,
not all devices have a valid Option ROM. In this case, the old
ice_get_orom_ver_info would "succeed" but report a version of all
zeros. The new implementation would fail to locate the $CIV section in
the Option ROM and report an error. Thus, we must ensure that
ice_init_nvm does not fail if ice_get_orom_ver_info fails.
Use the new ice_get_inactive_orom_ver to allow reporting the Option ROM
versions for a pending update via devlink info.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add a function to read the inactive netlist bank for version
information. To support this, refactor how we read the netlist version
data. Instead of using the firmware AQ interface with a module ID, read
from the flash as a flat NVM, using ice_read_flash_module.
This change requires a slight adjustment to the offset values used, as
reading from the flat NVM includes the type field (which was stripped by
firmware previously). Cleanup the macro names and move them to
ice_type.h. For clarity in how we calculate the offsets and so that
programmers can easily map the offset value to the data sheet, use
a wrapper macro to account for the offset adjustments.
Use the newly added ice_get_inactive_netlist_ver function to extract the
version data from the pending netlist module update. Add the stored
variants of "fw.netlist", and "fw.netlist.build" to the info version map
array.
With this change, we now report the "fw.netlist" and "fw.netlist.build"
versions into the stored section of the devlink info report. As with the
main NVM module versions, if there is no pending update, we report the
currently active values as stored.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The devlink info interface supports drivers reporting "stored" versions.
These versions indicate the version of an update that has been
downloaded to the device, but is not yet active.
The code for extracting the NVM version recently changed to enable
support for reading from either the active or the inactive bank. Use
this to implement ice_get_inactive_nvm_ver, which will read the NVM
version data from the inactive section of flash.
When reporting the versions via devlink info, first read the device
capabilities. Determine if there is a pending flash update, and if so,
extract relevant version information from the inactive flash. Store
these within the info context structure.
When reporting "stored" firmware versions, devlink documentation
indicates that we ought to always report a stored value, even if there
is no pending update. In this common case, the stored version should
match the running version. This means that each stored version should by
default fallback to the same value as reported by the running handler.
To support this, modify the version structure to have both a "getter"
and a "fallback". Modify the control loop so that it will use the
"fallback" function if the "getter" function does not report a version.
To report versions for which we can read the stored value, use a new
"stored()" macro. This macro will insert two entries into the version
list. The first entry is the traditional running version. The second is
the stored version, implemented with a fallback to the active version.
This is a little tricky, but reduces the overall duplication of elements
in the entry list, and ensures that running and stored values remain
consistent.
To avoid some duplication, add a combined() macro that will insert both
the running and stored versions into the version entry list.
Using this new support, add pending version reporter functions for
"fw.psid.api" and "fw.bundle_id". This enables reporting the stored
values for some of versions in the NVM module of the flash.
Reporting management versions is not implemented by this patch. The
active management version is reported to the driver via the AdminQ
mailbox during load. Although the version must be in the firmware binary
somewhere, accessing this from the inactive firmware is not trivial and
has not been implemented in this change.
Future changes will introduce support for reading the UNDI Option ROM
version and the version associated with the Netlist module.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add structures, identifiers, and helper functions for several AdminQ
commands related to performing a firmware update for the ice hardware.
These will be used in future code for implementing the devlink
.flash_update handler.
Signed-off-by: Cudzilo, Szymon T <szymon.t.cudzilo@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds functions to check for link override firmware support and get
the override settings for a port. The previously supported/default link
mode was strict mode.
In strict mode link is configured based on get PHY capabilities PHY types
with media.
Lenient mode is now the default link mode. In lenient mode the link is
configured based on get PHY capabilities PHY types without media. This
allows the user to configure link that the media does not report. Limit the
minimum supported link mode to 25G for devices that support 100G, and 1G
for devices that support less than 100G.
Default override is only supported in lenient mode. If default override
is supported and enabled, then default override values are used for
configuring speed and FEC. Default override provide persistent link
settings in the NVM.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add callbacks needed to support advanced power management for Wake on LAN.
Also make ice_pf_state_is_nominal function available for all configurations
not just CONFIG_PCI_IOV.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ice_get_pfa_module_tlv() and ice_read_sr_word() are not being called
outside of their file. Declare them as static.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Export a unique board identifier using "board.id" for devlink's
.info_get command.
Obtain this by reading the NVM for the PBA identification string.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The current implementation of .get_eeprom only enables reading from the
Shadow RAM portion of the NVM contents. Implement support for reading
the entire flash contents instead of only the initial portion contained
in the Shadow RAM.
A complete dump can take several seconds, but the ETHTOOL_GEEPROM ioctl
is capable of reading only a limited portion at a time by specifying the
offset and length to read.
In order to perform the reads directly, several functions are made non
static. Additionally, the unused ice_read_sr_buf_aq and ice_read_sr_buf
functions are removed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The NVM contents are read via firmware by using the ice_aq_read_nvm
function. This function has a couple of limits:
1) The AdminQ commands can only take buffers sized up to 4Kb. Thus, any
larger read must be split into multiple reads.
2) when reading from the Shadow RAM, reads must not cross sector
boundaries. The sectors are also 4Kb in size.
Implement the ice_read_flat_nvm function to read portions of the NVM by
flat offset. That is, to read using offsets from the start of the NVM
rather than from a specific module.
This function will be able to read both from the NVM and from the Shadow
RAM. For simplicity NVM reads will always be broken up to not cross 4Kb
page boundaries, even though this is not required unless reading from
the Shadow RAM.
Use this new function as the implementation of ice_read_sr_word_aq.
The ice_read_sr_buf_aq function is not modified here. This is because
a following change will remove the only caller of that function in favor
of directly using ice_read_flat_nvm. Thus, there is little benefit to
changing it now only to remove it momentarily. At the same time, the
ice_read_sr_aq function will also be removed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The Boot Configuration Section Block has been moved to the Preserved Field
Area (PFA) of NVM. Update the NVM reads that involves Boot Configuration
Section.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
