| Age | Commit message (Collapse) | Author |
|---|
|
The functions invoked via do_arch_prctl_common() can only operate on
the current task and none of these function uses the task argument.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/87lev7vtxj.ffs@tglx
|
|
The utilization of arch_scale_freq_tick() for CPU frequency readouts is
incomplete as it failed to move the function prototype and the define
out of the CONFIG_SMP && CONFIG_X86_64 #ifdef.
Make them unconditionally available.
Fixes: bb6e89df9028 ("x86/aperfmperf: Make parts of the frequency invariance code unconditional")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/lkml/202205010106.06xRBR2C-lkp@intel.com
|
|
Due to the avoidance of IPIs to idle CPUs arch_freq_get_on_cpu() can return
0 when the last sample was too long ago.
show_cpuinfo() has a fallback to cpufreq_quick_get() and if that fails to
return cpu_khz, but the readout code for the per CPU scaling frequency in
sysfs does not.
Move that fallback into arch_freq_get_on_cpu() so the behaviour is the same
when reading /proc/cpuinfo and /sys/..../cur_scaling_freq.
Suggested-by: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Doug Smythies <dsmythies@telus.net>
Link: https://lore.kernel.org/r/87pml5180p.ffs@tglx
|
|
Reading the current CPU frequency from /sys/..../scaling_cur_freq involves
in the worst case two IPIs due to the ad hoc sampling.
The frequency invariance infrastructure provides the APERF/MPERF samples
already. Utilize them and consolidate this with the /proc/cpuinfo readout.
The sample is considered valid for 20ms. So for idle or isolated NOHZ full
CPUs the function returns 0, which is matching the previous behaviour.
The resulting text size vs. the original APERF/MPERF plus the separate
frequency invariance code:
text: 2411 -> 723
init.text: 0 -> 767
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20220415161206.934040006@linutronix.de
|
|
The frequency invariance infrastructure provides the APERF/MPERF samples
already. Utilize them for the cpu frequency display in /proc/cpuinfo.
The sample is considered valid for 20ms. So for idle or isolated NOHZ full
CPUs the function returns 0, which is matching the previous behaviour.
This gets rid of the mass IPIs and a delay of 20ms for stabilizing observed
by Eric when reading /proc/cpuinfo.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20220415161206.875029458@linutronix.de
|
|
Now that the MSR readout is unconditional, store the results in the per CPU
data structure along with a jiffies timestamp for the CPU frequency readout
code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20220415161206.817702355@linutronix.de
|
|
The frequency invariance support is currently limited to x86/64 and SMP,
which is the vast majority of machines.
arch_scale_freq_tick() is called every tick on all CPUs and reads the APERF
and MPERF MSRs. The CPU frequency getters function do the same via dedicated
IPIs.
While it could be argued that on systems where frequency invariance support
is disabled (32bit, !SMP) the per tick read of the APERF and MPERF MSRs can
be avoided, it does not make sense to keep the extra code and the resulting
runtime issues of mass IPIs around.
As a first step split out the non frequency invariance specific
initialization code and the read MSR portion of arch_scale_freq_tick(). The
rest of the code is still conditional and guarded with a static key.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20220415161206.761988704@linutronix.de
|
|
Preparation for sharing code with the CPU frequency portion of the
aperf/mperf code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20220415161206.706185092@linutronix.de
|
|
Preparation for sharing code with the CPU frequency portion of the
aperf/mperf code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20220415161206.648485667@linutronix.de
|
|
AMD boot CPU initialization happens late via ACPI/CPPC which prevents the
Intel parts from being marked __init.
Split out the common code and provide a dedicated interface for the AMD
initialization and mark the Intel specific code and data __init.
The remaining text size is almost cut in half:
text: 2614 -> 1350
init.text: 0 -> 786
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20220415161206.592465719@linutronix.de
|
|
This code is convoluted and because it can be invoked post init via the
ACPI/CPPC code, all of the initialization functionality is built in instead
of being part of init text and init data.
As a first step create separate calls for the boot and the application
processors.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20220415161206.536733494@linutronix.de
|
|
as this can share code with the preexisting APERF/MPERF code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20220415161206.478362457@linutronix.de
|
|
aperfmperf_get_khz() already excludes idle CPUs from APERF/MPERF sampling
and that's a reasonable decision. There is no point in sending up to two
IPIs to an idle CPU just because someone reads a sysfs file.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20220415161206.419880163@linutronix.de
|
|
Fix the following scripts/kernel-doc warning:
arch/x86/kernel/process.c:412: warning: expecting prototype for tss_update_io_bitmap().
Prototype was for native_tss_update_io_bitmap() instead.
[ bp: Massage. ]
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220414062110.60343-1-jiapeng.chong@linux.alibaba.com
|
|
Commit
eac616557050 ("x86: Deprecate a.out support")
deprecated a.out support with the promise to remove it a couple of
releases later. That commit landed in v5.1.
Now it is more than a couple of releases later, no one has complained so
remove it.
Fold in a hunk removing the reference to arch/x86/ia32/ia32_aout.c in
MAINTAINERS:
https://lore.kernel.org/r/20220316050828.17255-1-lukas.bulwahn@gmail.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220113160115.5375-1-bp@alien8.de
|
|
Various mm code calls nodes_weight() to check if any bit of a given
nodemask is set.
This can be done more efficiently with nodes_empty() because nodes_empty()
stops traversing the nodemask as soon as it finds first set bit, while
nodes_weight() counts all bits unconditionally.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20220210224933.379149-26-yury.norov@gmail.com
|
|
In some cases, x86 code calls cpumask_weight() to check if any bit of a
given cpumask is set.
This can be done more efficiently with cpumask_empty() because
cpumask_empty() stops traversing the cpumask as soon as it finds first set
bit, while cpumask_weight() counts all bits unconditionally.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Link: https://lore.kernel.org/r/20220210224933.379149-17-yury.norov@gmail.com
|
|
In the x86 code __arch_set_user_pkey_access() is not used and is not
defined.
Remove the dead declaration.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220331180655.2946086-1-ira.weiny@intel.com
|
|
arch_set_user_pkey_access() was declared two times in the header.
Remove the 2nd declaration.
Suggested-by: "Edgecombe, Rick P" <rick.p.edgecombe@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220331180554.2945884-1-ira.weiny@intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of x86 fixes and updates:
- Make the prctl() for enabling dynamic XSTATE components correct so
it adds the newly requested feature to the permission bitmap
instead of overwriting it. Add a selftest which validates that.
- Unroll string MMIO for encrypted SEV guests as the hypervisor
cannot emulate it.
- Handle supervisor states correctly in the FPU/XSTATE code so it
takes the feature set of the fpstate buffer into account. The
feature sets can differ between host and guest buffers. Guest
buffers do not contain supervisor states. So far this was not an
issue, but with enabling PASID it needs to be handled in the buffer
offset calculation and in the permission bitmaps.
- Avoid a gazillion of repeated CPUID invocations in by caching the
values early in the FPU/XSTATE code.
- Enable CONFIG_WERROR in x86 defconfig.
- Make the X86 defconfigs more useful by adapting them to Y2022
reality"
* tag 'x86-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu/xstate: Consolidate size calculations
x86/fpu/xstate: Handle supervisor states in XSTATE permissions
x86/fpu/xsave: Handle compacted offsets correctly with supervisor states
x86/fpu: Cache xfeature flags from CPUID
x86/fpu/xsave: Initialize offset/size cache early
x86/fpu: Remove unused supervisor only offsets
x86/fpu: Remove redundant XCOMP_BV initialization
x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO
x86/config: Make the x86 defconfigs a bit more usable
x86/defconfig: Enable WERROR
selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test
x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RT signal fix from Thomas Gleixner:
"Revert the RT related signal changes. They need to be reworked and
generalized"
* tag 'core-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "signal, x86: Delay calling signals in atomic on RT enabled kernels"
|
|
Pull kvm fixes from Paolo Bonzini:
- Only do MSR filtering for MSRs accessed by rdmsr/wrmsr
- Documentation improvements
- Prevent module exit until all VMs are freed
- PMU Virtualization fixes
- Fix for kvm_irq_delivery_to_apic_fast() NULL-pointer dereferences
- Other miscellaneous bugfixes
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (42 commits)
KVM: x86: fix sending PV IPI
KVM: x86/mmu: do compare-and-exchange of gPTE via the user address
KVM: x86: Remove redundant vm_entry_controls_clearbit() call
KVM: x86: cleanup enter_rmode()
KVM: x86: SVM: fix tsc scaling when the host doesn't support it
kvm: x86: SVM: remove unused defines
KVM: x86: SVM: move tsc ratio definitions to svm.h
KVM: x86: SVM: fix avic spec based definitions again
KVM: MIPS: remove reference to trap&emulate virtualization
KVM: x86: document limitations of MSR filtering
KVM: x86: Only do MSR filtering when access MSR by rdmsr/wrmsr
KVM: x86/emulator: Emulate RDPID only if it is enabled in guest
KVM: x86/pmu: Fix and isolate TSX-specific performance event logic
KVM: x86: mmu: trace kvm_mmu_set_spte after the new SPTE was set
KVM: x86/svm: Clear reserved bits written to PerfEvtSeln MSRs
KVM: x86: Trace all APICv inhibit changes and capture overall status
KVM: x86: Add wrappers for setting/clearing APICv inhibits
KVM: x86: Make APICv inhibit reasons an enum and cleanup naming
KVM: X86: Handle implicit supervisor access with SMAP
KVM: X86: Rename variable smap to not_smap in permission_fault()
...
|
|
If apic_id is less than min, and (max - apic_id) is greater than
KVM_IPI_CLUSTER_SIZE, then the third check condition is satisfied but
the new apic_id does not fit the bitmask. In this case __send_ipi_mask
should send the IPI.
This is mostly theoretical, but it can happen if the apic_ids on three
iterations of the loop are for example 1, KVM_IPI_CLUSTER_SIZE, 0.
Fixes: aaffcfd1e82 ("KVM: X86: Implement PV IPIs in linux guest")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Message-Id: <1646814944-51801-1-git-send-email-lirongqing@baidu.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
FNAME(cmpxchg_gpte) is an inefficient mess. It is at least decent if it
can go through get_user_pages_fast(), but if it cannot then it tries to
use memremap(); that is not just terribly slow, it is also wrong because
it assumes that the VM_PFNMAP VMA is contiguous.
The right way to do it would be to do the same thing as
hva_to_pfn_remapped() does since commit add6a0cd1c5b ("KVM: MMU: try to
fix up page faults before giving up", 2016-07-05), using follow_pte()
and fixup_user_fault() to determine the correct address to use for
memremap(). To do this, one could for example extract hva_to_pfn()
for use outside virt/kvm/kvm_main.c. But really there is no reason to
do that either, because there is already a perfectly valid address to
do the cmpxchg() on, only it is a userspace address. That means doing
user_access_begin()/user_access_end() and writing the code in assembly
to handle exceptions correctly. Worse, the guest PTE can be 8-byte
even on i686 so there is the extra complication of using cmpxchg8b to
account for. But at least it is an efficient mess.
(Thanks to Linus for suggesting improvement on the inline assembly).
Reported-by: Qiuhao Li <qiuhao@sysec.org>
Reported-by: Gaoning Pan <pgn@zju.edu.cn>
Reported-by: Yongkang Jia <kangel@zju.edu.cn>
Reported-by: syzbot+6cde2282daa792c49ab8@syzkaller.appspotmail.com
Debugged-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Tested-by: Maxim Levitsky <mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Fixes: bd53cb35a3e9 ("X86/KVM: Handle PFNs outside of kernel reach when touching GPTEs")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When emulating exit from long mode, EFER_LMA is cleared with
vmx_set_efer(). This will already unset the VM_ENTRY_IA32E_MODE control
bit as requested by SDM, so there is no need to unset VM_ENTRY_IA32E_MODE
again in exit_lmode() explicitly. In case EFER isn't supported by
hardware, long mode isn't supported, so exit_lmode() cannot be reached.
Note that, thanks to the shadow controls mechanism, this change doesn't
eliminate vmread or vmwrite.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20220311102643.807507-3-zhenzhong.duan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
vmx_set_efer() sets uret->data but, in fact if the value of uret->data
will be used vmx_setup_uret_msrs() will have rewritten it with the value
returned by update_transition_efer(). uret->data is consumed if and only
if uret->load_into_hardware is true, and vmx_setup_uret_msrs() takes care
of (a) updating uret->data before setting uret->load_into_hardware to true
(b) setting uret->load_into_hardware to false if uret->data isn't updated.
Opportunistically use "vmx" directly instead of redoing to_vmx().
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20220311102643.807507-2-zhenzhong.duan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
It was decided that when TSC scaling is not supported,
the virtual MSR_AMD64_TSC_RATIO should still have the default '1.0'
value.
However in this case kvm_max_tsc_scaling_ratio is not set,
which breaks various assumptions.
Fix this by always calculating kvm_max_tsc_scaling_ratio regardless of
host support. For consistency, do the same for VMX.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220322172449.235575-8-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Remove some unused #defines from svm.c
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220322172449.235575-7-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Another piece of SVM spec which should be in the header file
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220322172449.235575-6-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Due to wrong rebase, commit
4a204f7895878 ("KVM: SVM: Allow AVIC support on system w/ physical APIC ID > 255")
moved avic spec #defines back to avic.c.
Move them back, and while at it extend AVIC_DOORBELL_PHYSICAL_ID_MASK to 12
bits as well (it will be used in nested avic)
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220322172449.235575-5-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
If MSR access is rejected by MSR filtering,
kvm_set_msr()/kvm_get_msr() would return KVM_MSR_RET_FILTERED,
and the return value is only handled well for rdmsr/wrmsr.
However, some instruction emulation and state transition also
use kvm_set_msr()/kvm_get_msr() to do msr access but may trigger
some unexpected results if MSR access is rejected, E.g. RDPID
emulation would inject a #UD but RDPID wouldn't cause a exit
when RDPID is supported in hardware and ENABLE_RDTSCP is set.
And it would also cause failure when load MSR at nested entry/exit.
Since msr filtering is based on MSR bitmap, it is better to only
do MSR filtering for rdmsr/wrmsr.
Signed-off-by: Hou Wenlong <houwenlong.hwl@antgroup.com>
Message-Id: <2b2774154f7532c96a6f04d71c82a8bec7d9e80b.1646655860.git.houwenlong.hwl@antgroup.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When RDTSCP is supported but RDPID is not supported in host,
RDPID emulation is available. However, __kvm_get_msr() would
only fail when RDTSCP/RDPID both are disabled in guest, so
the emulator wouldn't inject a #UD when RDPID is disabled but
RDTSCP is enabled in guest.
Fixes: fb6d4d340e05 ("KVM: x86: emulate RDPID")
Signed-off-by: Hou Wenlong <houwenlong.hwl@antgroup.com>
Message-Id: <1dfd46ae5b76d3ed87bde3154d51c64ea64c99c1.1646226788.git.houwenlong.hwl@antgroup.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
HSW_IN_TX* bits are used in generic code which are not supported on
AMD. Worse, these bits overlap with AMD EventSelect[11:8] and hence
using HSW_IN_TX* bits unconditionally in generic code is resulting in
unintentional pmu behavior on AMD. For example, if EventSelect[11:8]
is 0x2, pmc_reprogram_counter() wrongly assumes that
HSW_IN_TX_CHECKPOINTED is set and thus forces sampling period to be 0.
Also per the SDM, both bits 32 and 33 "may only be set if the processor
supports HLE or RTM" and for "IN_TXCP (bit 33): this bit may only be set
for IA32_PERFEVTSEL2."
Opportunistically eliminate code redundancy, because if the HSW_IN_TX*
bit is set in pmc->eventsel, it is already set in attr.config.
Reported-by: Ravi Bangoria <ravi.bangoria@amd.com>
Reported-by: Jim Mattson <jmattson@google.com>
Fixes: 103af0a98788 ("perf, kvm: Support the in_tx/in_tx_cp modifiers in KVM arch perfmon emulation v5")
Co-developed-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20220309084257.88931-1-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
It makes more sense to print new SPTE value than the
old value.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220302102457.588450-1-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
AMD EPYC CPUs never raise a #GP for a WRMSR to a PerfEvtSeln MSR. Some
reserved bits are cleared, and some are not. Specifically, on
Zen3/Milan, bits 19 and 42 are not cleared.
When emulating such a WRMSR, KVM should not synthesize a #GP,
regardless of which bits are set. However, undocumented bits should
not be passed through to the hardware MSR. So, rather than checking
for reserved bits and synthesizing a #GP, just clear the reserved
bits.
This may seem pedantic, but since KVM currently does not support the
"Host/Guest Only" bits (41:40), it is necessary to clear these bits
rather than synthesizing #GP, because some popular guests (e.g Linux)
will set the "Host Only" bit even on CPUs that don't support
EFER.SVME, and they don't expect a #GP.
For example,
root@Ubuntu1804:~# perf stat -e r26 -a sleep 1
Performance counter stats for 'system wide':
0 r26
1.001070977 seconds time elapsed
Feb 23 03:59:58 Ubuntu1804 kernel: [ 405.379957] unchecked MSR access error: WRMSR to 0xc0010200 (tried to write 0x0000020000130026) at rIP: 0xffffffff9b276a28 (native_write_msr+0x8/0x30)
Feb 23 03:59:58 Ubuntu1804 kernel: [ 405.379958] Call Trace:
Feb 23 03:59:58 Ubuntu1804 kernel: [ 405.379963] amd_pmu_disable_event+0x27/0x90
Fixes: ca724305a2b0 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM")
Reported-by: Lotus Fenn <lotusf@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Like Xu <likexu@tencent.com>
Reviewed-by: David Dunn <daviddunn@google.com>
Message-Id: <20220226234131.2167175-1-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Trace all APICv inhibit changes instead of just those that result in
APICv being (un)inhibited, and log the current state. Debugging why
APICv isn't working is frustrating as it's hard to see why APICv is still
inhibited, and logging only the first inhibition means unnecessary onion
peeling.
Opportunistically drop the export of the tracepoint, it is not and should
not be used by vendor code due to the need to serialize toggling via
apicv_update_lock.
Note, using the common flow means kvm_apicv_init() switched from atomic
to non-atomic bitwise operations. The VM is unreachable at init, so
non-atomic is perfectly ok.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220311043517.17027-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add set/clear wrappers for toggling APICv inhibits to make the call sites
more readable, and opportunistically rename the inner helpers to align
with the new wrappers and to make them more readable as well. Invert the
flag from "activate" to "set"; activate is painfully ambiguous as it's
not obvious if the inhibit is being activated, or if APICv is being
activated, in which case the inhibit is being deactivated.
For the functions that take @set, swap the order of the inhibit reason
and @set so that the call sites are visually similar to those that bounce
through the wrapper.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220311043517.17027-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Use an enum for the APICv inhibit reasons, there is no meaning behind
their values and they most definitely are not "unsigned longs". Rename
the various params to "reason" for consistency and clarity (inhibit may
be confused as a command, i.e. inhibit APICv, instead of the reason that
is getting toggled/checked).
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220311043517.17027-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
There are two kinds of implicit supervisor access
implicit supervisor access when CPL = 3
implicit supervisor access when CPL < 3
Current permission_fault() handles only the first kind for SMAP.
But if the access is implicit when SMAP is on, data may not be read
nor write from any user-mode address regardless the current CPL.
So the second kind should be also supported.
The first kind can be detect via CPL and access mode: if it is
supervisor access and CPL = 3, it must be implicit supervisor access.
But it is not possible to detect the second kind without extra
information, so this patch adds an artificial PFERR_EXPLICIT_ACCESS
into @access. This extra information also works for the first kind, so
the logic is changed to use this information for both cases.
The value of PFERR_EXPLICIT_ACCESS is deliberately chosen to be bit 48
which is in the most significant 16 bits of u64 and less likely to be
forced to change due to future hardware uses it.
This patch removes the call to ->get_cpl() for access mode is determined
by @access. Not only does it reduce a function call, but also remove
confusions when the permission is checked for nested TDP. The nested
TDP shouldn't have SMAP checking nor even the L2's CPL have any bearing
on it. The original code works just because it is always user walk for
NPT and SMAP fault is not set for EPT in update_permission_bitmask.
Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Message-Id: <20220311070346.45023-5-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Comments above the variable says the bit is set when SMAP is overridden
or the same meaning in update_permission_bitmask(): it is not subjected
to SMAP restriction.
Renaming it to reflect the negative implication and make the code better
readability.
Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Message-Id: <20220311070346.45023-4-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The commit 09f037aa48f3 ("KVM: MMU: speedup update_permission_bitmask")
refactored the code of update_permission_bitmask() and change the
comments. It added a condition into a list to match the new code,
so the number/order for conditions in the comments should be updated
too.
Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Message-Id: <20220311070346.45023-3-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Change the type of access u32 to u64 for FNAME(walk_addr) and
->gva_to_gpa().
The kinds of accesses are usually combinations of UWX, and VMX/SVM's
nested paging adds a new factor of access: is it an access for a guest
page table or for a final guest physical address.
And SMAP relies a factor for supervisor access: explicit or implicit.
So @access in FNAME(walk_addr) and ->gva_to_gpa() is better to include
all these information to do the walk.
Although @access(u32) has enough bits to encode all the kinds, this
patch extends it to u64:
o Extra bits will be in the higher 32 bits, so that we can
easily obtain the traditional access mode (UWX) by converting
it to u32.
o Reuse the value for the access kind defined by SVM's nested
paging (PFERR_GUEST_FINAL_MASK and PFERR_GUEST_PAGE_MASK) as
@error_code in kvm_handle_page_fault().
Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Message-Id: <20220311070346.45023-2-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
It isn't OK to cache the dirty status of a page in internal structures
for an indefinite period of time.
Any time a vCPU exits the run loop to userspace might be its last; the
VMM might do its final check of the dirty log, flush the last remaining
dirty pages to the destination and complete a live migration. If we
have internal 'dirty' state which doesn't get flushed until the vCPU
is finally destroyed on the source after migration is complete, then
we have lost data because that will escape the final copy.
This problem already exists with the use of kvm_vcpu_unmap() to mark
pages dirty in e.g. VMX nesting.
Note that the actual Linux MM already considers the page to be dirty
since we have a writeable mapping of it. This is just about the KVM
dirty logging.
For the nesting-style use cases (KVM_GUEST_USES_PFN) we will need to
track which gfn_to_pfn_caches have been used and explicitly mark the
corresponding pages dirty before returning to userspace. But we would
have needed external tracking of that anyway, rather than walking the
full list of GPCs to find those belonging to this vCPU which are dirty.
So let's rely *solely* on that external tracking, and keep it simple
rather than laying a tempting trap for callers to fall into.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220303154127.202856-3-dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Replace the guest_uses_pa and kernel_map booleans in the PFN cache code
with a unified enum/bitmask. Using explicit names makes it easier to
review and audit call sites.
Opportunistically add a WARN to prevent passing garbage; instantating a
cache without declaring its usage is either buggy or pointless.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220303154127.202856-2-dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Include kvm_cache_regs.h to pick up the definition of is_guest_mode(),
which is referenced by nested_svm_virtualize_tpr() in svm.h. Remove
include from svm_onhpyerv.c which was done only because of lack of
include in svm.h.
Fixes: 883b0a91f41ab ("KVM: SVM: Move Nested SVM Implementation to nested.c")
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Peter Gonda <pgonda@google.com>
Message-Id: <20220304161032.2270688-1-pgonda@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The third nybble of AMD's event select overlaps with Intel's IN_TX and
IN_TXCP bits. Therefore, we can't use AMD64_RAW_EVENT_MASK on Intel
platforms that support TSX.
Declare a raw_event_mask in the kvm_pmu structure, initialize it in
the vendor-specific pmu_refresh() functions, and use that mask for
PERF_TYPE_RAW configurations in reprogram_gp_counter().
Fixes: 710c47651431 ("KVM: x86/pmu: Use AMD64_RAW_EVENT_MASK for PERF_TYPE_RAW")
Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220308012452.3468611-1-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Re-introduce zapping only leaf SPTEs in kvm_zap_gfn_range() and
kvm_tdp_mmu_unmap_gfn_range(), this time without losing a pending TLB
flush when processing multiple roots (including nested TDP shadow roots).
Dropping the TLB flush resulted in random crashes when running Hyper-V
Server 2019 in a guest with KSM enabled in the host (or any source of
mmu_notifier invalidations, KSM is just the easiest to force).
This effectively revert commits 873dd122172f8cce329113cfb0dfe3d2344d80c0
and fcb93eb6d09dd302cbef22bd95a5858af75e4156, and thus restores commit
cf3e26427c08ad9015956293ab389004ac6a338e, plus this delta on top:
bool kvm_tdp_mmu_zap_leafs(struct kvm *kvm, int as_id, gfn_t start, gfn_t end,
struct kvm_mmu_page *root;
for_each_tdp_mmu_root_yield_safe(kvm, root, as_id)
- flush = tdp_mmu_zap_leafs(kvm, root, start, end, can_yield, false);
+ flush = tdp_mmu_zap_leafs(kvm, root, start, end, can_yield, flush);
return flush;
}
Cc: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20220325230348.2587437-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
As guest_irq is coming from KVM_IRQFD API call, it may trigger
crash in svm_update_pi_irte() due to out-of-bounds:
crash> bt
PID: 22218 TASK: ffff951a6ad74980 CPU: 73 COMMAND: "vcpu8"
#0 [ffffb1ba6707fa40] machine_kexec at ffffffff8565b397
#1 [ffffb1ba6707fa90] __crash_kexec at ffffffff85788a6d
#2 [ffffb1ba6707fb58] crash_kexec at ffffffff8578995d
#3 [ffffb1ba6707fb70] oops_end at ffffffff85623c0d
#4 [ffffb1ba6707fb90] no_context at ffffffff856692c9
#5 [ffffb1ba6707fbf8] exc_page_fault at ffffffff85f95b51
#6 [ffffb1ba6707fc50] asm_exc_page_fault at ffffffff86000ace
[exception RIP: svm_update_pi_irte+227]
RIP: ffffffffc0761b53 RSP: ffffb1ba6707fd08 RFLAGS: 00010086
RAX: ffffb1ba6707fd78 RBX: ffffb1ba66d91000 RCX: 0000000000000001
RDX: 00003c803f63f1c0 RSI: 000000000000019a RDI: ffffb1ba66db2ab8
RBP: 000000000000019a R8: 0000000000000040 R9: ffff94ca41b82200
R10: ffffffffffffffcf R11: 0000000000000001 R12: 0000000000000001
R13: 0000000000000001 R14: ffffffffffffffcf R15: 000000000000005f
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffffb1ba6707fdb8] kvm_irq_routing_update at ffffffffc09f19a1 [kvm]
#8 [ffffb1ba6707fde0] kvm_set_irq_routing at ffffffffc09f2133 [kvm]
#9 [ffffb1ba6707fe18] kvm_vm_ioctl at ffffffffc09ef544 [kvm]
RIP: 00007f143c36488b RSP: 00007f143a4e04b8 RFLAGS: 00000246
RAX: ffffffffffffffda RBX: 00007f05780041d0 RCX: 00007f143c36488b
RDX: 00007f05780041d0 RSI: 000000004008ae6a RDI: 0000000000000020
RBP: 00000000000004e8 R8: 0000000000000008 R9: 00007f05780041e0
R10: 00007f0578004560 R11: 0000000000000246 R12: 00000000000004e0
R13: 000000000000001a R14: 00007f1424001c60 R15: 00007f0578003bc0
ORIG_RAX: 0000000000000010 CS: 0033 SS: 002b
Vmx have been fix this in commit 3a8b0677fc61 (KVM: VMX: Do not BUG() on
out-of-bounds guest IRQ), so we can just copy source from that to fix
this.
Co-developed-by: Yi Liu <liu.yi24@zte.com.cn>
Signed-off-by: Yi Liu <liu.yi24@zte.com.cn>
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Message-Id: <20220309113025.44469-1-wang.yi59@zte.com.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
If kvm->arch.tdp_mmu_zap_wq cannot be created, the failure has
to be propagated up to kvm_mmu_init_vm and kvm_arch_init_vm.
kvm_arch_init_vm also has to undo all the initialization, so
group all the MMU initialization code at the beginning and
handle cleaning up of kvm_page_track_init.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
"Assorted bits and pieces"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
aio: drop needless assignment in aio_read()
clean overflow checks in count_mounts() a bit
seq_file: fix NULL pointer arithmetic warning
uml/x86: use x86 load_unaligned_zeropad()
asm/user.h: killed unused macros
constify struct path argument of finish_automount()/do_add_mount()
fs: Remove FIXME comment in generic_write_checks()
|
