| Age | Commit message (Collapse) | Author |
|---|
|
Add dt nodes for generic-ehci/ohci host controller.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Use serial0 alias to select stdout-path on Cygnus bcm911360_entphon
board.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add nodes for peripherals in Cygnus dtsi: sdhci, keypad, spi, dma,
pinmux configs.
Signed-off-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add PMU capability to Cygnus so trace and performance profiling
can be used.
Signed-off-by: Jason Uy <jason.uy@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Move v3d devicetree node to proper address ordered location in Cygnus
dtsi.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Fix incorrect Cygnus UART2 register base.
Fixes: 0f0b21a83ad2 ("ARM: dts: Move all Cygnus peripherals into axi bus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This pull request brings in a new SMP enable-method compat string,
which is needed to move the 32-bit SMP boot code out of the irqchip.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Fixes commit 687c27676151 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")
This patch corrects an issue where the cd-gpios was improperly setup
using IRQ_TYPE_LEVEL_LOW instead of GPIO_ACTIVE_LOW.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Latest update to the BeagleBoard-X15 platform (revision C). This board contains
a silicon update (Rev 2.0), which includes a fix for the 2nd ethernet phy when
running at 1000 Mbps speeds.
This board can be indentified by the [C.00] after [BBRDX15_] in the at24 eeprom:
[BBRDX15_C.001731PX150249]
Rev C is now in full production and boards are available for end users.
https://beagleboard.org/x15
https://github.com/beagleboard/beagleboard-x15/
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Nishanth Menon <nm@ti.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Override the compatible string of the first USB controller to enable
device mode.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Override the compatible string of the first USB controller to enable
device mode.
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Override the compatible string of the first USB controller to enable
device mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Override the compatible string of the first USB controller to enable
device mode.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Use newly added R-Car SATA Gen2 fallback compat string
in the DT of the r8a7791 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before the fallback compat string is considered.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Use newly added R-Car SATA Gen2 fallback compat string
in the DT of the r8a7790 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before the fallback compat string is considered.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 32-bit DT changes for v4.14" from Kevin Hilman:
- update clock controler for use as reset controller
- misc. updates/fixups/improvements
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson6: use stable UART bindings
ARM: dts: meson: mark the clock controller also as reset controller
ARM: dts: meson: add a node which describes the SRAM
ARM: dts: meson8b: use the existing wdt node to override the compatible
ARM: dts: meson8: add the PWM controller nodes
ARM: dts: move the pwm_ab and pwm_cd nodes to meson.dtsi
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Pull "ARM: Keystone DTS for 4.14" from Santosh Shilimkar:
Contents:
- ti-sci power domain, clock and reset controller support
- DSP nodes for k2h/k2l/k2e evms
- DSP CMA memory pools for k2h/k2l/k2e/keg evms
- MMC/hsmmc suport for k2g
- eDMA support for k2g
- DCAN support for k2g
* tag 'keystone_dts_for_4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: (22 commits)
ARM: dts: keystone-k2g-ice: Add and enable DSP CMA memory pool
ARM: dts: keystone-k2g-evm: Add and enable DSP CMA memory pool
ARM: dts: keystone-k2g: Add DSP node
ARM: dts: k2g: Add DCAN nodes
dt-bindings: net: c_can: Update binding for clock and power-domains property
ARM: dts: keystone-k2g-evm: Enable MMC0 and MMC1
ARM: dts: keystone-k2g: add MMC0 and MMC1 nodes
ARM: dts: keystone-k2g: Add eDMA nodes
dt-bindings: ti,omap-hsmmc: Add 66AK2G mmc controller
dt-bindings: ti,edma: Add 66AK2G specific information
ARM: dts: keystone-k2g: Add gpio nodes
ARM: dts: keystone-k2e-evm: Add and enable DSP CMA memory pool
ARM: dts: keystone-k2l-evm: Add and enable common DSP CMA memory pool
ARM: dts: keystone-k2hk-evm: Add and enable common DSP CMA memory pool
ARM: dts: keystone-k2e: Add DSP node
ARM: dts: keystone-k2l: Add DSP nodes
ARM: dts: keystone-k2hk: Add DSP nodes
ARM: dts: keystone-k2g: Add TI SCI reset-controller node
ARM: dts: keystone-k2g: Add ti-sci clock provider node
ARM: dts: keystone-k2g: Add ti-sci power domain node
...
|
|
Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.
- clock-latency = 300 us
Approximate worst-case latency to do clock transition for every
OPPs. Using an arbitrary safe value similar to r8a7791(R-Car M2) Soc.
- operating-points = < kHz - uV >
List of 6 operating points. All of them are using the same voltage
since DVS is not supported in RZ/G1 Soc.
Note:This also fixes the below errors seen on kernel logs
[ 0.876877] cpu cpu0: dev_pm_opp_get_opp_count: OPP table not found (-19)
[ 0.883727] cpu cpu1: cpufreq_init: failed to get clk: -2
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add DT nodes for the Advanced Power Management Unit (APMU) and the
second CPU core. Use the enable-method to point out that the APMU
should be used for SMP support.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Document APMU and SMP enable method for RZ/G1M
(also known as r8a7743) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Document the iW-RainboW-G22D device tree bindings.
It is just a placeholder for the time being, the actual
implementation is not available yet.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Document the iW-RainboW-G22M-SM SODIMM System on Module device tree
bindings. It is just a placeholder for the time being, the actual
implementation is not available yet.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The adv7511 on the Koelsch board has a 12 MHz fixed clock
for the CEC block. Specify this in the dts to enable CEC support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt
Pull "Qualcomm Device Tree Changes for v4.14" from Andy Gross:
* Fixup XO, timer nodes, and pinctrl on IPQ4019
* Add IPQ4019 RNG and wifi blocks
* Update MSM8974 coresight node
* Add IPQ8074 bindings
* tag 'qcom-dts-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: qcom: add and enable both wifi blocks on the IPQ4019
ARM: dts: qcom-msm8974: dts: Update coresight replicator
ARM: dts: qcom: add pseudo random number generator on the IPQ4019
ARM: dts: ipq4019: Move xo and timer nodes to SoC dtsi
ARM: dts: ipq4019: Fix pinctrl node name
dt-bindings: qcom: Add IPQ8074 bindings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
Pull "UniPhier ARM SoC DT updates for v4.14" from Masahiro Yamada:
- complete migrating to SPDX License Identifier
- remove support for old SoC
- add nodes for NAND, Audio pinctrl
- replace /include/ with #include
* tag 'uniphier-dt-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: add Denali NAND controller node
ARM: dts: uniphier use #include instead of /include/
ARM: dts: uniphier: remove sLD3 SoC support
ARM: dts: uniphier: add audio out pin-mux node
ARM: dts: uniphier: use SPDX-License-Identifier (2nd)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Device tree changes for omaps for v4.14 merge window" from Tony Lindgren:
- A series of changes for dra7 and am572 to use generic
MMC vqmmc regulator
- Clean-up tps65217 internal interrupts to define them
only in tps65217.dtsi
- Add dra7 iodelay pinctrl driver configuration
- Add buzzer support for am437x-gp-evm
- Disable HDMI CEC internal pull-ups as it seems that
all boards have an external pull for these
- Remove unnecessary interrupt-parent for omap3
- Configure droid 4 vaudio regulator initial mode and
add vibrator
- Enable NAND dma prefetch for am335x-evm, am437x and dra7
- Add pcie1 dt node for EP mode for am57x and dra7
- Add support for new dra76x SoCs and dra76x-evm
* tag 'omap-for-v4.14/dt-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: dts: nokia n900: update dts with camera support
ARM: dts: Add support for dra76-evm
ARM: dts: Add support for dra76x family of devices
ARM: dts: DRA7: Add pcie1 dt node for EP mode
ARM: dts: am335x: add support for Moxa UC-8100-ME-T open platform
ARM: dts: dra7xx: Enable NAND dma prefetch by default
ARM: dts: am437xx: Enable NAND dma prefetch by default
ARM: dts: am335x-evm: Enable NAND dma prefetch by default
ARM: dts: omap4-droid4: Add vibrator
ARM: dts: motorola-cpcap-mapphone: set initial mode for vaudio
ARM: dts: omap3: Remove needless interrupt-parent property
ARM: dts: Disable HDMI CEC internal pull-ups
ARM: dts: am437x-gp-evm: Add support for buzzer
ARM: dts: Add dra7 iodelay configuration
ARM: dts: tps65217: Add power button interrupt to the common tps65217.dtsi file
ARM: dts: tps65217: Add charger interrupts to the common tps65217.dtsi file
ARM: dts: omap*: Replace deprecated "vmmc_aux" with "vqmmc"
ARM: dts: am572x-idk: Fix GPIO polarity for MMC1 card detect
ARM: dts: am571x-idk: Fix GPIO polarity for MMC1 card detect
ARM: dts: dra7: Add "max-frequency" property to MMC dt nodes
...
|
|
Pull "mvebu dt for 4.14 (part 1)" from Gregory CLEMENT:
Add arm_global_timer node on Armada 38x
Fix PCI bus dtc warnings on mvebu 32 bits device tree files
* tag 'mvebu-dt-4.14-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-38x: Add arm_global_timer node
ARM: dts: marvell: fix PCI bus dtc warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "Gemini DTS updates for ARM SoC take one" from Linus Walleij:
* tag 'gemini-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: gemini: add pin control set-up for the SoC
ARM: dts: Add DTS file for D-Link DIR-685
ARM: dts: gemini: Switch to using macros
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner dts changes for 4.14" from Chen-Yu Tsai:
The usual improvement patches:
- R_INTC interrupt controller compatible string update and device node
addition
- Battery charger enabled on the Cubietruck
- New board: Bananapi M2 Magic
- Ethernet and USB OTG enabled on the Beelink X2
- MMC enabled for A83T boards
* tag 'sunxi-dt-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a83t: h8homlet: Enable micro-SD card and onboard eMMC
ARM: dts: sun8i: a83t: cubietruck-plus: Enable micro-SD card and eMMC
ARM: dts: sun8i: a83t: Add pingroup for 8-bit eMMC on mmc2
ARM: dts: sun8i: a83t: Add MMC controller device nodes
ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2
ARM: dts: sun8i: h3: Enable USB OTG on the Beelink X2
ARM: dts: sun8i: Add BananaPI M2-Magic DTS
ARM: dts: sun7i: enable battery power supply subnode on cubietruck
ARM: dts: sun8i: a83t: Add device node for R_INTC interrupt controller
ARM: dts: sun8i: a23/a33: Use new sun6i-a31-r-intc compatible for NMI/R_INTC
ARM: dts: sun6i: a31: Use new sun6i-a31-r-intc compatible for NMI/R_INTC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 changes for 4.14" from Heiko Stübner:
Removal of the deprectated num-slots property from all Rockchip dw-mmc
nodes. The rv1108 gains support for sd-cards on the evaluation board and
the general nodes get a bit of cosmetic. On rk3288 the evb gains support
saradc and the adc-key connected to it while some more boards also get
their mali gpu enabled (fennec, evb, tinker).
The biggest set of changes can be found on the rk3228/rk3229 combo this
time. It gets core support for efuse, sdmmc, sdio, io-domans and spdif
as well as a separate rk3229.dtsi that will keep the slight differences
between the two brothers rk3228/rk3229. The evaluation board also gets
some attention and abled nodes (regulators, io-domains, emmc, tsadc keys)
But I think the most interesting change is the cpu enable-method for it.
Instead of using the older in-kernel method, we're now also moving to
handling this in firmware via the psci interface on 32bit Rockchip socs.
In a recently merged pull request [0] support for the rk3228/rk3229 was
added to OP-TEE including the psci support and it seems supporting other
32bit Rockchip socs that way is also planned for the future.
[0] https://github.com/OP-TEE/optee_os/pull/1666
* tag 'v4.14-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (23 commits)
ARM: dts: rockchip: fix property-ordering in rv1108 mmc nodes
ARM: dts: rockchip: enable sdmmc for rv1108 evb
ARM: dts: rockchip: add efuse device node for rk3228
ARM: dts: rockchip: add gpio power-key for rk3229-evb
ARM: dts: rockchip: enable tsadc for rk3229-evb
ARM: dts: rockchip: enable eMMC for rk3229-evb
ARM: dts: rockchip: enable io-domain for rk3229-evb
ARM: dts: rockchip: add cpu-supply property for cpu node of rk3229-evb
ARM: dts: rockchip: add regulator nodes for rk3229-evb
ARM: dts: rockchip: add sdmmc and sdio nodes for rk3228 SoC
ARM: dts: rockchip: fix compatible string for eMMC node of rk3228 SoC
ARM: dts: rockchip: add cpu enable method for rk3228 SoC
ARM: dts: rockchip: remove num-slots from all platforms
ARM: dts: rockchip: Add io-domain node for rk3228
ARM: dts: rockchip: add basic dtsi file for RK3229 SoC
ARM: dts: rockchip: enable adc key for rk3288-evb
ARM: dts: rockchip: enable saradc for rk3288-evb
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-fennec
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-evb
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-tinker
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.14" from Simon Horman:
Changes of note:
* Add pin controller support to the RZ/G1M (r8a7743) SoC and
RZ/A1 (r7s72100) SoCs now that the driver is available in v4.13-rc1.
* Add GPIO support to the RZ/G1M (r8a7743) SoC now that the driver
is availabe in v4.13-rc1.
* Enable MMCIF0 and Ethernet AVB support on the RZ/G1M (r8a7743) SoC and
the iWave-RZG1M-20M Qseven SOM. This depends on newly added pin
controller support noted above.
* Use R-Car Gen 2 fallback binding for vin nodes
This makes binding use consistent across R-Car Gen 2 SoCs.
It does not have any run-time effect
* Use SMP jump stub SRAM region from DT on R-Car Gen 2 SoCs
Geert Uytterhoeven says, "The R-Car Gen2 platform code for CPU core
bringup needs to copy a jump stub to on-SoC SRAM. Currently it uses a
hardcoded address pointing to ICRAM1."
* Add Inter Connect RAM to R-Car Gen 2 and RZ/G1 SoCs
Geert Uytterhoeven says, "R-Car Gen2 and RZ/G1 SoCs contain two or three
blocks of SRAM, which can be used for several purposes. One such purpose
is holding a jump stub for CPU core bringup."
* Use generic compatible string for I2C EEPROM for RZ/A1 (r7s72100) SoC
and koelsch board.
This is part of a tree-wide cleanup by Javier Martinez Canillas
* tag 'renesas-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (38 commits)
ARM: dts: iwg20m: Correct indentation of mmcif0 properties
ARM: dts: rskrza1: Add LED0 pin support
ARM: dts: rskrza1: Add SDHI1 pin group
ARM: dts: rskrza1: Add Ethernet pin group
ARM: dts: rskrza1: Add SCIF2 pin group
ARM: dts: genmai: Add ethernet pin group
ARM: dts: genmai: Add user led device nodes
ARM: dts: genmai: Add RIIC2 pin group
ARM: dts: genmai: Add SCIF2 pin group
ARM: dts: r7s72100: Add pin controller node
ARM: dts: iwg20m: Add MMCIF0 support
ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for vin nodes
ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for vin nodes
ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for vin nodes
ARM: dts: r8a7743: Add MMCIF0 support
ARM: dts: r8a7794: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7793: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7792: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7791: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7790: Reserve SRAM for the SMP jump stub
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Bindings Updates for v4.14" from Simon Horman:
* Document R-Car D3 (r8a77995) SoC and Draak board
* Document reserved SRAM for the SMP jump stub on R-Car Gen2 and RZ/G1 SoCs
Geert Uytterhoeven says, "+Renesas R-Car Gen2 and RZ/G1 SoCs need a small
piece of SRAM for the jump stub +for secondary CPU bringup and CPU
hotplug. +This memory is reserved by adding a child node to a
"mmio-sram" node..."
* Add a VSP channel index to DU vsps
Laurent Pinchart says, "multiple LIF instances in the VSP. The current DT
bindings don't support specifying that kind of SoC integration scheme.
Extend them with a VSP channel index."
* Add R-Car M3-W (r8a7796) HDMI TX DT bindings
This is compatible with existing R-Car H3 (r8a7795) support
* tag 'renesas-dt-bindings-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Document Renesas Draak board DT bindings
ARM: shmobile: Document R-Car D3 SoC DT bindings
dt-bindings: display: rcar-du: Add a VSP channel index to the vsps DT property
dt-bindings: sram: Document renesas,smp-sram
dt-bindings: display: renesas: Add R-Car M3-W HDMI TX DT bindings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt
Pull "STM32 DT updates for v4.14, round 1" from Alexandre Torgue:
Highlights:
----------
-Add DMA support on STM32F746
-Add DMA support on STM32H743
-Add DAC support on STM32H743
-Add DAC support on STM32F429
-Add ADC support on STM32H743
-Enable ADC on stm32h743i-eval board
-Add CEC support on STM32F7xx MCUs
-Enable CEC on stm32f769-disco board
-Remove rdinit from stm32f4 boards
* tag 'stm32-dt-for-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Add DMA support for STM32H743 SoC
ARM: dts: stm32: Add DMA support for STM32F746 SoC
ARM: dts: stm32: enable ADC on stm32h743i-eval board
ARM: dts: stm32: add ADC support on stm32h743
ARM: dts: stm32: Add DAC support on stm32h743
ARM: dts: stm32: Add DAC support on stm32f429
ARM: dts: stm32: enable CEC for stm32f769 discovery
ARM: dts: stm32: add CEC for stm32f7 family
ARM: dts: stm32: reorder stm32h743 nodes
ARM: dts: stm32: Remove rdinit from bootargs on stm32f429-disco
ARM: dts: stm32: Remove rdinit from bootargs on stm32f429i-eval
ARM: dts: stm32: Remove rdinit from bootargs on stm32f469-disco
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DTS ARM changes for v4.13" from Krzysztof Kozłowski:
Remove deprecated and unneeded properties from Exynos boards.
* tag 'samsung-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Remove num-slots from exynos platforms
ARM: dts: exynos: Remove the OF graph from DSI node
|
|
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra71-evm.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra72-evm-revc.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra72-evm.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74x SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am572x-idk.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am571x-idk.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AM572x IDK and AM571x IDK boards have equivalent
design of how SD card and eMMC are connected.
The two EVMs mainly differ in IOdelay configuration
needed (because of difference in SoC used).
Move the common properties to am57xx-idk-common.dtsi
file which is common for both EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am57xx-beagle-x15/am57xx-beagle-x15-revb1.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra7-evm.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add pinmux configuration for MMC module including IODELAY
values suggested in the data manual for the various supported
modes.
IOdelay data for both silicon revision 1.1 and 2.0 is
added here.
The datamanual revisions used are:
* AM572x Silicon Revision 2.0: SPRS953B, Revised November 2016
* AM572x Silicon Revision 1.1: SPRS915R, Revised November 2016
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add pinmux configuration for MMC module including IODELAY
values suggested in the data manual for the various supported
modes.
IOdelay data for both silicon revision 1.0 and 2.0 is
added here.
The datamanual revisions used are:
* AM571x Silicon Revision 2.0: SPRS957D, Revised January 2017
* AM571x Silicon Revision 1.0: SPRS919M, Revised November 2017
* DRA71x : SPRS960B, Revised February 2017
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add NAND controller node to LD4, Pro4, sLD8, Pro5, and PXs2.
Set up pinctrl to enable 2 chip select lines except Pro4. The CS1
for Pro4 is multiplexed with other peripherals such as UART2, so
I did not enable it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
To include dt-bindings headers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add the (previously omitted) Ether/PHY pin data to the SK-RZG1E board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add the (previously omitted) SCIF2 pin data to the SK-RZG1E board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the generic R8A7745 part of the PFC device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add SPI device tree node for rv1108.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
